manualshive.com logo in svg

HP ProLiant DL60 Gen9, User Manual, Page: 39 / 127

Share
Download
HP ProLiant DL60 Gen9 User Manual Download Page 39

 

Hardware options installation  39 

2. 

Remove the drive blank. 

 

3. 

Prepare the drive. 

 

4. 

Install the drive. 

 

5. 

Determine the status of the drive from the drive LED definitions ("

Hot-plug drive LED definitions

" on 

page 

13

). 

6. 

If removed, install the security bezel ("

Security bezel option

" on page 

36

). 

To configure arrays, see the 

HPE Smart Storage Administrator User Guide

 on the Hewlett Packard 

Enterprise website (

http://www.hpe.com/info/smartstorage/docs

). 

 

Storage controller options 

The server ships with an embedded Dynamic Smart Array B140i Controller. This embedded controller is 

supported in UEFI Boot Mode only. For more information about the controller and its features, see the 

HPE Dynamic Smart Array B140i RAID Controller User Guide

 on the Hewlett Packard Enterprise website 

(

http://www.hpe.com/info/smartstorage/docs

). 

Upgrade options exist for an integrated array controller. For a list of supported options, see the product 

QuickSpecs on the Hewlett Packard Enterprise website (

http://www.hpe.com/info/qs

). 

Summary of Contents for ProLiant DL60 Gen9
































































































































Reviews:

No comments