HP ProLiant DL60 Gen9 User Manual Download Page 36 | Manualshive

Page: 36 / 127

background image

Hardware options installation 36

Hardware options installation

Introduction

If more than one option is being installed, read the installation instructions for all the hardware options and

identify similar steps to streamline the installation process.

WARNING:

To reduce the risk of personal injury from hot surfaces, allow the drives and the

internal system components to cool before touching them.

CAUTION:

To prevent damage to electrical components, properly ground the server before

beginning any installation procedure. Improper grounding can cause electrostatic discharge.

Security bezel option

The security bezel helps prevent unauthorized physical access to the front panel components.
The security bezel is only supported in servers using the quick-release latch rack ears.
Install the security bezel and then lock it with the key provided with the kit.

Drive options

The server supports up to four LFF hot-plug or non hot-plug drives.
The embedded storage controller supports SATA drive installation.
For SAS drive installation, install a Host Bus Adapter or a Smart Array Controller board option. For more

information about product features, specifications, options, configurations, and compatibility, see the

product QuickSpecs on the Hewlett Packard Enterprise website (

http://www.hpe.com/info/qs

«
...
34
35
36
37
38
...
»

Summary of Contents for ProLiant DL60 Gen9
































































































































Reviews:

No comments

Related manuals for ProLiant DL60 Gen9

Brand: IBM Pages: 54

Express 5800 Series

Brand: NEC Pages: 90

PDS-220F Series

Brand: ICP DAS USA Pages: 94

Brand: Galleon Pages: 35

8649 - Eserver xSeries 225

Brand: IBM Pages: 194

Modbus Server-FC330A

Brand: IntesisBox Pages: 5

Brand: Conceptronic Pages: 127

Brand: HIKVISION Pages: 13

EDIMAX FAST ETHERNET MFP SERVER VERSION: 2.0

Brand: Edimax Pages: 118

WLNG-AN-DP500 Series

Brand: Quatech Pages: 120

Brand: TRENDnet Pages: 135

Brand: Ekselans Pages: 37

SPARC Enterprise M3000

Brand: Fujitsu Pages: 202

SPARC Enterprise M4000

Brand: Fujitsu Pages: 310

SPARC Enterprise M3000

Brand: Fujitsu Pages: 560

SPARC Enterprise M4000

Brand: Fujitsu Pages: 76

Brand: Asus Pages: 98

Brand: Asus Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands