HP ProDesk 400 G4 Maintenance And Service Manual Download Page 15

Page: 15 / 132

Description

512-GB, self-encrypted solid-state drive with OPAL2 and TLC

256-GB, SATA-3 solid-state drive

256-GB, 2280 M.2, NVMe solid-state drive with SS

256-GB, 2280 M.2, NVMe solid-state drive with SS and TLC

256-GB, self-encrypted solid-state drive with OPAL2 and TLC

128-GB, SATA-3 solid-state drive

Miscellaneous parts

Description

Power cord with C13 receptacle, 1.83-meter (6.00-feet)

For use in Argentina

For use in Australia and New Zealand

For use in Brazil

For use in Denmark

For use in Europe

For use in Israel

For use in Italy

For use in the People’s Republic of China

For use in South Africa

For use in South Korea

For use in Switzerland

For use in Taiwan

For use in the United Kingdom and Singapore

Power cord with C13 receptacle, 1.83-meter (6.00-feet) 5-15P for use in Thailand

Power cord with C13 receptacle, 1.83-meter (6.00-feet) 6-amp for use in India

Power cord with Option-949 adapter ROHS

Adapters:

HP DisplayPort–to–DVI SL adapter

HP DisplayPort–to–HDMI 1.4 adapter

HP DisplayPort–to–VGA adapter

HP USB Type-C–to–DisplayPort adapter

HP USB Type-C–to–USB 3.0 adapter

Cables:

Miscellaneous parts

Summary of Contents for ProDesk 400 G4





































































































































Search results

Summary of Contents for ProDesk 400 G4

Reviews:

Related manuals for ProDesk 400 G4

Brands by name

Popular brands

HP ProDesk 400 G4, Maintenance And Service Manual

Search results

Summary of Contents for ProDesk 400 G4

Reviews:

Related manuals for ProDesk 400 G4

Brands by name

Popular brands