background image

 

Installing the chassis  33 

   

   

 

CAUTION: 

For proper cooling, be sure every switch module bay and uplink module bay has either 

a blank or a module installed. 

   

To install the component: 

1.

 

Remove the uplink module bay blank ("

Removing the uplink module blank

" on page 

32

). 

2.

 

Prepare the uplink module for installation. 

 

3.

 

Install the uplink module. 

 

4.

 

Do one of the following: 

o

 

If the switch module is already installed, verify the uplink module powers on and the uplink module 
health LED is green. 

o

 

If the switch module is not installed, install the switch module before verifying LEDs. 

For more information, see "Switch information and guidelines (on page 

29

).

5.

 

After both components have been installed, verify the switch firmware is at the HP recommended 

firmware version. For more information, see the HP Moonshot Component Pack download website 
 

Installing the switch module 

   

 

CAUTION: 

  To avoid connectivity loss, do not remove switches already in operation. 

   

Summary of Contents for Moonshot 1500

































































Reviews: