HP ML350 - ProLiant - G2 Maintenance And Service Manual Download Page 60

Page: 60 / 78

Component identification 60

Component identification

In this section

Front panel components .......................................................................................................................... 60

Front panel LEDs and buttons................................................................................................................... 61
Rear panel components........................................................................................................................... 62

Rear panel LEDs and buttons ................................................................................................................... 63

System board components....................................................................................................................... 64

System board LEDs ................................................................................................................................. 66
System LEDs and internal health LED combinations ..................................................................................... 67

SAS and SATA hard drive LEDs ............................................................................................................... 68

SAS and SATA hard drive LED combinations............................................................................................. 68

Front panel components

Item Description

Removable media bays (4)

2 CD-ROM

drive

Hot-plug hard drive bays (8-bay drive cage model)

Hot-plug hard drive bays (6-bay drive cage model)

USB connectors (2)

Summary of Contents for ML350 - ProLiant - G2















































































Search results

Summary of Contents for ML350 - ProLiant - G2

Reviews:

Related manuals for ML350 - ProLiant - G2

Brands by name

Popular brands

HP ML350 - ProLiant - G2, Maintenance And Service Manual

Search results

Summary of Contents for ML350 - ProLiant - G2

Reviews:

Related manuals for ML350 - ProLiant - G2

Brands by name

Popular brands