HP ML350 - ProLiant - G2 Maintenance And Service Manual Download Page 53

Page: 53 / 78

Cabling 53

Cabling

In this section

Optional SATA or SAS cabling................................................................................................................ 53

Standard SATA cabling .......................................................................................................................... 53
Optional ATA or ATAPI device cabling ..................................................................................................... 53

Optional SATA or SAS cabling

Many configurations are possible when SATA or SAS controllers are added. When upgrading the

storage controller, refer to the Quickspecs and the cabling matrix to identify the correct cables

(

http://h10010.www1.hp.com/wwpc/pscmisc/vac/us/en/ss/proliant/proliant-ml.html

Standard SATA cabling

Item Description

SATA cable (drives 1-4)

SATA cable (drives 5-8)

Optional ATA or ATAPI device cabling

This server includes one IDE cable (the Cable Select Cable) that can connect up to two ATA or ATAPI

devices to the system through the integrated IDE controller. This cable has three clearly labeled

connectors. If only one IDE device is connected to the system, it must be secured to the cable connector

labeled Drive 0. For all IDE devices, set the configuration jumpers to "Cable Select" or "CS."

Summary of Contents for ML350 - ProLiant - G2















































































Search results

Summary of Contents for ML350 - ProLiant - G2

Reviews:

Related manuals for ML350 - ProLiant - G2

Brands by name

Popular brands

HP ML350 - ProLiant - G2, Maintenance And Service Manual

Search results

Summary of Contents for ML350 - ProLiant - G2

Reviews:

Related manuals for ML350 - ProLiant - G2

Brands by name

Popular brands