background image

 

1 System 

Requirements 

ISC consists of console software and instrumentation software.  You install and 
run console software on the system from which you are going to monitor and 
control other servers referred to as managed servers.  A managed server is an 
Intel

®

 Architecture (IA) platform with ISC Platform Instrumentation software 

installed and running.  The system running the console software is sometimes 
referred to as the client workstation or client. 

Client Workstation 

The client workstation runs console software.  The console software is installed 
during ISC installation.  Table 1 lists the system configurations on which the ISC 
installation process installs console software and also lists the client workstation’s 
configuration requirements and restrictions: 

Table 1.  Client Workstation Configuration Requirements and Restrictions 

System Configuration 

Requirements 

IA-32 platforms running 
Windows 2000 

• 

Intel Pentium microprocessor or higher. 

• 

At least 64 MB of RAM. 

• 

At least 150 MB of available disk space. 

• 

Microsoft Windows compatible modem must be used 
if you connect to the server by modem. 

• 

Service Pack 2 must be installed. 

Itanium™ - based 
platforms running 
Microsoft Windows 
64-bit Advanced Server 

• 

Supported console for DPC only. 

• 

Intel® Itanium microprocessor. 

• 

At least 512 MB of RAM. 

• 

At least 150 MB of available disk space. 

• 

Microsoft Windows compatible modem must be used 
if you connect to the server by modem. 

IA-32 platforms running 
Windows NT

 4.0 server 

or workstation, Enterprise 
Edition 

• 

Supported console for DPC only. 

• 

Windows 2000/NT Server, or Workstation 4.0 (Service 
Pack 6a), or Enterprise Edition. 

• 

Intel Pentium microprocessor or higher. 

• 

At least 64 MB of RAM. 

• 

At least 150 MB of available disk space. 

• 

For Windows NT, Remote Access Service must also 
be installed. If it is not installed, the Direct Platform 
Control (DPC) component will not install. 

• 

Microsoft Windows compatible modem must be used 
if you connect to the server by modem. 

• 

No support for Java-based Platform Instrumentation 
Control (PIC). 

Summary of Contents for Integrity rx4610

















Reviews: