manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

The HP FlexNetwork 5130 HI series is a versatile network switch offering exceptional performance and flexibility. To maximize your user experience, you can conveniently access the comprehensive Command Reference Manual for free download from manualshive.com. Explore the extensive capabilities of this product with our user-friendly manual.

Share
Download
background image

20 

Syntax 

interface interface-type

 

interface-number 

Views 

System view 

Predefined user roles 

network-admin 

Parameters 

interface-type

: Specifies an interface type. 

interface-number

: Specifies an interface number. 

Examples 

# Enter GigabitEthernet 1/0/1 interface view. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] 

 

jumboframe enable 

Use 

jumboframe enable 

to allow jumbo frames within the specified length to pass through. 

Use 

undo jumboframe enable 

to prevent jumbo frames from passing through. 

Syntax 

jumboframe enable 

[ 

value

 ] 

undo jumboframe enable 

Default 

The device allows jumbo frames within 10000 bytes to pass through. 

Views 

Ethernet interface view 

Predefined user roles 

network-admin 

Parameters 

value

: Sets the maximum length of Ethernet frames that are allowed to pass through. The value 

range is 1536 to 10000 bytes. 

Usage guidelines 

If you set the 

value

 argument multiple times, the most recent configuration takes effect. 

Examples 

# Enable jumbo frames to pass through GigabitEthernet 1/0/1.  

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] jumboframe enable 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Related manuals for FlexNetwork 5130 HI series

Ubiquiti ES-24-250W Quick Start Manual preview
ES-24-250W
Brand: Ubiquiti Pages: 24
Ubiquiti USW-24 User Manual preview
USW-24
Brand: Ubiquiti Pages: 13
Ubisys ZIGBEE S2(-R) Quick Start Manual preview
ZIGBEE S2(-R)
Brand: Ubisys Pages: 2
Edimax GS-1016 Datasheet preview
GS-1016
Brand: Edimax Pages: 2
ORVIBO ZigBee Mini Hub Faq preview
ZigBee Mini Hub
Brand: ORVIBO Pages: 3
Cooper Crouse-Hinds CEAG KO Operating Instructions Manual preview
Crouse-Hinds CEAG KO
Brand: Cooper Pages: 12
Linksys SRW208L Product Data preview
SRW208L
Brand: Linksys Pages: 3
KCC KTD-600 Series Manual preview
KTD-600 Series
Brand: KCC Pages: 6
Icy Box IB-AC618 Manual preview
IB-AC618
Brand: Icy Box Pages: 6
Eaton Edison Cooper Power Series Installation And Operation Instructions Manual preview
Edison Cooper Power Series
Brand: Eaton Pages: 12
Velleman HQ-Power VMS4 Manual preview
HQ-Power VMS4
Brand: Velleman Pages: 5
Eaton STS 2000A Installation And Operation Manual preview
STS 2000A
Brand: Eaton Pages: 120
Canoga Perkins HS8000 Quick Start Manual preview
HS8000
Brand: Canoga Perkins Pages: 7
GarrettCom PS14H-48VDC Installation And User Manual preview
PS14H-48VDC
Brand: GarrettCom Pages: 77
ATEN Master View CS-74A User Manual preview
Master View CS-74A
Brand: ATEN Pages: 16
Xantech HD88C Installation Instructions Manual preview
HD88C
Brand: Xantech Pages: 12
Zigen ZIG-SW42 User Manual preview
ZIG-SW42
Brand: Zigen Pages: 18
Buffalo BS-GU2005 Hardware Manual preview
BS-GU2005
Brand: Buffalo Pages: 2

Brands by name

Popular brands

Load more brands