HP FlexNetwork 5130 HI series Command Reference Manual Download Page 258

Page: 258 / 306

250

LLDP commands

display lldp local-information

Use

display lldp local-information

to display local LLDP information, which will be contained in the

advertisable LLDP TLVs and sent to neighboring devices.

Syntax

display lldp local-information

[

global

interface interface-type interface-number

]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

global

: Displays the global local LLDP information.

interface

interface-type interface-number

: Specifies a port by its type and number.

Usage guidelines

If no keyword or argument is specified, this command displays all local LLDP information, which
includes the following:

•

The global LLDP information.

•

The LLDP information about the LLDP-enabled ports in up state.

Examples

# Display all local LLDP information.

<Sysname> display lldp local-information

Global LLDP local-information:

Chassis ID : 0079-9556-d080

System name : HPE

System description : HPE Comware Platform Software, Software Version 7.1.045,

Release 1121

HPE 5130 24G PoE+ 4SFP+ 1-slot HI Switch

Development LP

System capabilities supported : Bridge, Router, Customer Bridge, Service Bridge

System capabilities enabled : Bridge, Router, Customer Bridge

MED information:

Device class : Connectivity device

MED inventory information of master board:

HardwareRev : Ver.A

FirmwareRev : 103

SoftwareRev : 7.1.045 Alpha 1102

SerialNum : 210235A1G00000000001

Manufacturer name : HPE

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands