HP FlexNetwork 5130 HI series Command Reference Manual Download Page 252

Page: 252 / 306

244

Views

Ethernet interface view, aggregate interface view

Predefined user roles

network-admin

Parameters

hex-value

: Sets a hexadecimal TPID value in the range of 0x0001 to 0xFFFF, excluding the reserved

EtherType values listed in

Table 55

Usage guidelines

A service provider-side port uses the SVLAN TPID to replace the TPID in outgoing frames' SVLAN
tags, in addition to matching incoming tagged frames.

Examples

# Set the SVLAN TPID to 0x9100 on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qinq ethernet-type service-tag 9100

qinq transparent-vlan

Use

qinq transparent-vlan

to enable transparent transmission for a list of VLANs on a port.

Use

undo qinq transparent-vlan

to disable transparent transmission for a list of VLANs on a port.

Syntax

qinq transparent-vlan vlan-id-list

undo qinq transparent-vlan

{

vlan-id-list

all

}

Default

Transparent transmission is disabled for all VLANs on a port.

Views

Layer 2 Ethernet interface view, Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

vlan-id-list

: Specifies a space-separated list of up to 10 VLAN items. Each item specifies a single

VLAN ID or a VLAN ID range in the form of

vlan-id1

vlan-id2

. The value range for VLAN IDs is 1 to

4094. The end VLAN ID must be equal to or greater than the start VLAN ID.

all

: Specifies all existing VLANs.

Usage guidelines

By default, QinQ tags all incoming frames with the PVID on a port. This command disables QinQ to
tag incoming traffic from a list of VLANs. These VLANs are called transparent VLANs.

To ensure successful transmission for a transparent VLAN, follow these configuration guidelines:

•

Set the link type of the port to trunk or hybrid, and assign the port to its PVID and the transparent
VLAN.

•

Do not configure any other VLAN manipulation actions for the transparent VLAN on the port.

•

Make sure all ports on the traffic path permit the transparent VLAN to pass through.

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands

HP FlexNetwork 5130 HI series, Command Reference Manual

Search results

Summary of Contents for FlexNetwork 5130 HI series

Reviews:

Related manuals for FlexNetwork 5130 HI series

Brands by name

Popular brands