manualshive.com logo in svg

HP FlexNetwork 5130 HI series, Command Reference Manual

Share
Download
HP FlexNetwork 5130 HI series Command Reference Manual Download Page 251

 

243 

Predefined user roles 

network-admin 

Parameters 

hex-value

: Sets a hexadecimal TPID value in the range of 0x0001 to 0xFFFF, excluding the reserved 

EtherType values listed in 

Table 55

. 

Table 55 Reserved EtherType values 

Protocol type 

Value 

ARP 0x0806 

PUP 0x0200 

RARP 0x8035 

IP 0x0800 

IPv6 0x86DD 

PPPoE 0x8863/0x8864 

MPLS 0x8847/0x8848 

IPX/SPX 0x8137 

IS-IS 0x8000 

LACP 0x8809 

802.1X 0x888E 

LLDP 0x88CC 

802.1ag 0x8902 

Cluster 0x88A7 

Reserved 0xFFFD/0xFFFE/0xFFFF 

 

Usage guidelines 

A QinQ-enabled port uses the CLAN TPID to match incoming tagged frames. An incoming frame is 
handled as an untagged frame if its TPID is different from the CVLAN TPID. 

Examples 

# Set the TPID value in CVLAN tags to 0x8200. 

<Sysname> system-view 

[Sysname] qinq ethernet-type customer-tag 8200 

qinq ethernet-type

 

service-tag 

Use 

qinq ethernet-type service-tag

 to configure the SVLAN TPID. 

Use 

undo qinq ethernet-type service-tag

 to restore the default SVLAN TPID. 

Syntax 

qinq ethernet-type

 

service-tag

 

hex-value

 

undo qinq ethernet-type service-tag 

Default 

The SVLAN TPID is 0x8100. 

Summary of Contents for FlexNetwork 5130 HI series



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands