HP FlexFabric 7900 Series Command Reference Manual Download Page 268

Page: 268 / 294

260

•

Assigning an IRF physical interface to or reclaiming an IRF physical interface from an MDC
causes the following problems:

{

The IRF configuration on the interface is lost.

{

The IRF link is closed.

To avoid IRF fabric split, make sure each member device always has a minimum of one IRF link
in up state.

Examples

# Assign FortyGigE 1/0/1 through FortyGigE 1/0/6 to MDC

sub1

<Sysname> system-view

[Sysname] mdc sub1

[Sysname-mdc-2-sub1] allocate interface fortygige 1/0/1 to fortygige 1/0/6

Configuration of the interfaces will be lost. Continue? [Y/N]:y

Execute the location slot command in this view to make the configuration take effect.

display mdc

Use

display mdc

to display MDCs and their status.

Syntax

display mdc

[

name

mdc-name

]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

name

mdc-name

: Specifies an MDC by its name, a case-sensitive string of 1 to 15 characters. If you

do not specify this option, the command displays all MDCs.

Examples

# Display all MDCs.

<Sysname> display mdc

ID Name Status

1 Admin active

2 sub1 inactive

Table 44 Command output

Field Description

Status

Status of the MDC:

•

inactive

—The MDC is stopped or not started yet.

•

starting

—The device is executing the

mdc start

command to start the MDC.

•

active

—The MDC is operating correctly.

•

updating

—The device is executing the

location

command to authorize the MDC

to use an LPU

•

stopping

—The device is executing the

undo mdc start

command to stop the

Summary of Contents for FlexFabric 7900 Series







































































































































































































































































































Search results

Summary of Contents for FlexFabric 7900 Series

Reviews:

Related manuals for FlexFabric 7900 Series

Brands by name

Popular brands

HP FlexFabric 7900 Series, Command Reference Manual

Search results

Summary of Contents for FlexFabric 7900 Series

Reviews:

Related manuals for FlexFabric 7900 Series

Brands by name

Popular brands