background image

Deployment of Red Hat Linux 7.2 for Itanium™ Processor on ProLiant DL590/64 Servers 

 

Device Support for Red Hat Linux 7.2 for Itanium 
Processor 

Red Hat Linux 7.2 for Itanium Processor is a 64-bit operating system with a true 64-bit kernel. 
Any code that executes in kernel mode, such as drivers, must be developed specifically to 
interface correctly with the 64-bit kernel. Therefore, drivers that were developed for any 32-bit 
versions of Red Hat Linux will not function properly under Red Hat Linux 7.2 for Itanium 
Processor. 

Supported Storage Options 

IMPORTANT:

  Providing support for storage options on the ProLiant DL590/64 requires 

drivers that have been ported to the 64-bit architecture. The 32-bit drivers used on other Compaq 
server platforms will not load or function properly on ProLiant DL590/64 servers. As a result, 
only the storage options displayed in Table 2 are supported for use in ProLiant DL590/64 servers. 
Attempting to install unsupported storage options and drivers into the ProLiant DL590/64 may 
render the system unusable. 

Table 2 lists supported Compaq storage options and drivers needed to interface with Red Hat 
Linux 7.2 for Itanium Processor. 

Table 2. Supported Compaq storage options 

Option 

Driver 

Location 

Compaq 64-bit/66MHz Dual Channel Wide Ultra 
3 SCSI Adapter 

aic7xxx 

Red Hat CD 

Compaq 64-bit/66MHz Single Channel Wide 
Ultra 3 SCSI Adapter 

aic7xxx 

Red Hat CD 

Compaq Integrated Smart Array Controller 

cpqarray

1

 

Red Hat CD 

Compaq Smart Array 5300 Controller 

cciss

1

 

Red Hat CD 

Compaq Smart Array 532 Controller 

cciss

1

 

Red Hat CD 

Compaq StorageWorks 64-bit/33 MHz PCI-to-
Fibre Channel Host Bus Adapter 

cpqfc 

Red Hat CD 

IDE CD-ROM 

 

Red Hat CD 

IDE LS-120 Removable Media Drive 

 

Red Hat CD 

1

 Driver is included in the install kernel. 

Supported Network Interface Controllers 

Table 3 lists Compaq network interface controllers supported for use with the ProLiant DL590/64 
running Red Hat Linux 7.2 for Itanium Processor.  

Table 3. Supported Compaq network interface controllers 

Compaq NIC 

Driver 

Location 

Compaq NC3123 Fast Ethernet NIC PCI 10/100 
WOL 

e100 

Red Hat CD 

Compaq NC3134 Fast Ethernet NIC 64 PCI 
Dual Port 10/100 

e100 

Red Hat CD 

continued 

16S6-0502A-WWEN 
 

Summary of Contents for DL590/64










Reviews: