manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

7–38

376220-001

Service Reference Guide, dc5100

Removal and Replacement Procedures— Small Form Factor (SFF) Chassis

7.15 Speaker 

1. Prepare the computer for disassembly (

Section 7.1, “Preparation for Disassembly”

).

2. Remove the computer cover (

Section 7.4, “Computer Cover”

).

3. Remove the fan shroud.

 

Section 7.10, “Fan Shroud”

4. Remove the heatsink control cable and the heatsink from the system board (

Section 7.13, 

“Heatsink”).

5. Remove any memory modules that might interfere with the screwdriver used for removing 

the speaker.

6. Disconnect the speaker wire from the system board.

7. Remove the two screws

 

that secure the speaker to the chassis.

8. Remove the speaker from the chassis.

To install the speaker, reverse the removal procedures.

Ä

CAUTION: 

Before reinstalling the heatsink you must clean the top of the processor and the bottom of the 

heatsink with an alcohol pad supplied in the speaker spares kit. After the alcohol has evaporated, apply 
thermal grease to the top of the processor from the syringe supplied in the speaker spares kit.

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

IBM 360 Operating Manual preview
360
Brand: IBM Pages: 48
Zenith Z-100 Series Technical Manual preview
Z-100 Series
Brand: Zenith Pages: 493
AURES K750 V1.3.indb User Manual preview
K750 V1.3.indb
Brand: AURES Pages: 63
Gateway 03-DT009-01S User Manual preview
03-DT009-01S
Brand: Gateway Pages: 108
S&T Kontron KBox E-410-APL User Manual preview
Kontron KBox E-410-APL
Brand: S&T Pages: 78
Prentke Romich Company Accent 700 Hardware Manual preview
Accent 700
Brand: Prentke Romich Company Pages: 36
ZAHNER Zennium Installation & Getting Started preview
Zennium
Brand: ZAHNER Pages: 24
Sun Microsystems Sun Ultra 450 Manual preview
Sun Ultra 450
Brand: Sun Microsystems Pages: 45
Vivo DESK-V000A Instruction Manual preview
DESK-V000A
Brand: Vivo Pages: 3
Vivo DESK-V000R Instruction Manual preview
DESK-V000R
Brand: Vivo Pages: 3
Vivo DESK-V000W Instruction Manual preview
DESK-V000W
Brand: Vivo Pages: 3
Contec BX-951-DC series User Manual preview
BX-951-DC series
Brand: Contec Pages: 111
PowerCenter 120 User Manual preview
120
Brand: PowerCenter Pages: 29
Broage NBOOK Quick Manual preview
NBOOK
Brand: Broage Pages: 11
Rockwell Automation Allen-Bradley VersaView 5000 ThinManager Series User Manual preview
Allen-Bradley VersaView 5000 ThinManager Series
Brand: Rockwell Automation Pages: 72
3Com e-PC c10/s10 User Manual preview
e-PC c10/s10
Brand: 3Com Pages: 122
EverFocus eIVP-CML-AI-D0000 User Manual preview
eIVP-CML-AI-D0000
Brand: EverFocus Pages: 19
UTC RETAIL 2600 User Manual preview
2600
Brand: UTC RETAIL Pages: 10

Brands by name

Popular brands

Load more brands