HP Compaq dc5100 Series Service & Reference Manual Download

Page: 146 / 230

7–34

376220-001

Service Reference Guide, dc5100

Removal and Replacement Procedures— Small Form Factor (SFF) Chassis

7.12 Power Switch Assembly

1. Prepare the computer for disassembly (

Section 7.1, “Preparation for Disassembly”

2. Remove the computer cover (

Section 7.4, “Computer Cover”

3. Disconnect the power switch/LED cable from the system board.

4. Squeeze the switch holder retaining clips together at the front of the chassis

and push the

switch assembly out of the chassis

. Push the two LEDs out of the chassis

5. If necessary, the LED holders may also be removed by squeezing the clips and pushing them

out of the front of the chassis

To install the power switch and LEDs, reverse the removal procedure.

Summary of Contents for Compaq dc5100 Series







































































































































































































































Search results

Summary of Contents for Compaq dc5100 Series

Reviews:

Related manuals for Compaq dc5100 Series

Brands by name

Popular brands

HP Compaq dc5100 Series, Service & Reference Manual

Search results

Summary of Contents for Compaq dc5100 Series

Reviews:

Related manuals for Compaq dc5100 Series

Brands by name

Popular brands