HP Compaq dc5000 MT Reference Manual Download Page 98

Page: 98 / 180

7–4

360201-002

Service Reference Guide, dc5000

Removal and Replacement Procedures— Small Form Factor (SFF) Chassis

7.3 Computer Access Panel

1. Prepare the computer for disassembly (

Section 7.1, “Preparation for Disassembly”

CAUTION:

Before removing the computer access panel, ensure that the computer is turned off and that

the power cord is disconnected from the electrical outlet.

2. Pull up and hold open the latch on the top of the computer

3. Slide the computer access panel

back about 0.5inch (1.3 cm), then lift it off the unit.

When installing the access panel, press down on its center to ensure the latches are properly
secured while sliding it into the locked position.

Summary of Contents for Compaq dc5000 MT





















































































































































































Search results

Summary of Contents for Compaq dc5000 MT

Reviews:

Related manuals for Compaq dc5000 MT

Brands by name

Popular brands

HP Compaq dc5000 MT, Reference Manual

Search results

Summary of Contents for Compaq dc5000 MT

Reviews:

Related manuals for Compaq dc5000 MT

Brands by name

Popular brands