HP c3700 - Workstation Installation Manual Download Page 2

$/usr/sbin/swlist -l bundle | grep HWE

(for Hardware Enablement patches)

The output should contain information similar to this:

XSWGR1100...   General Release Patches, November 1999 (ACE)

or

HWE1100...   Hardware Enablement Patches for HP-UX 11.00, March 2002 (HWE)

If you do not see lines like this in the output, you should install the appropriate patch bundles
(November 1999 or later ACE and March 2002 or later HWE) before attempting to install the Fire
GL-UX software.

Multi-display configurations - The j6000 and j6700 Workstations can be configured to run multiple
Fire GL-UX cards in a multi-display environment. At this time, HP does not support the Single Logi-
cal Screen functionality with the Fire GL-UX card. You cannot use multiple Fire GL-UX cards in the
c3650 or c3700 Workstations. You also cannot use the Fire GL-UX card concurrently with any other
type of graphics card.

Monitor Support

An HP-supported, full multimode color monitor is required for the Fire GL-UX card.

The following list of monitors, plus all other monitors that HP supports in the future, are supported
with the Fire GL-UX card

NOTE

The Fire GL-UX card does not support all timings and resolutions that each display
device will accept. Use the HP System Administration Manager (SAM) utility to select
alternative settings.

See your workstation Owner's Guide for information on using the

/opt/graphics/common/bin/

setmon

 command to produce a list of supported timings and screen resolutions for your workstation.

Table 0-1. Fire GL-UX Supported Monitors

Product

Name

Product Number

Description

A4490A

17-inch color CRT monitor

P920

D8912W

19-inch color CRT monitor

P910

D8910W

19-inch color CRT monitor

A4575A

19-inch color CRT monitor

P1130

P4819W

21-inch color CRT monitor

P1120

D8915W

21-inch color CRT monitor

P1110

D2847W

21-inch color CRT monitor

A4576A

21-inch color CRT monitor

A7217A

24-inch color CRT monitor

A1295A

24-inch color CRT monitor

L1820

P4829W

18-inch color LCD flat panel (quartz gray bezel)

L1820

P4829X

18-inch color LCD flat panel (dark gray bezel)

L1810

D5069W

18-inch color LCD flat panel

L1800

D5065W

18-inch color LCD flat panel

Summary of Contents for c3700 - Workstation










Reviews: