manualshive.com logo in svg

HP Aruba 7010 Series, Installation Manual, Page: 10 / 28

Share
Download
HP Aruba 7010 Series Installation Manual Download Page 10

10

| 7010 Controller

Aruba 7010 Series Controller

| Installation Guide

The following table describes the LED behavior for each mode:  

Uplink Ports 

The Aruba 7010 controller includes two 1000BASE-X uplink ports (16 and 17). See 

Figure 4

. It is recommended to use 

Aruba supported SFP transceivers in these ports. 

Figure 4  

Ports, LEDs, and LCD Panel 

Table 5  

10/100/1000BASE-T Ethernet Port LEDs

LED

Function LCD Mode

Indicator

Status

LINK/ACT Link 

status

N/A

Green (Solid)

Link has been established 

Green 

(Blinking)

Port is transmitting or receiving data 

Off

No link on port 

STATUS

Port 

status

Administrativ

e

Green (Solid)

Port enabled 

Off

Port Administratively disabled 

Duplex

Green (Solid)

Full-duplex 

Off

Half-duplex 

PoE

Green (Solid)

PoE enabled 

Green 

(Blinking)

Power enabled, but power denied due to 

unavailability 

Off

PoE not enabled 

Speed

Green (Solid)

1000 Mbps 

Off

10/100 Mbps 

Summary of Contents for Aruba 7010 Series





























Reviews:

No comments