manualshive.com logo in svg

HP Aruba 2930F Series, Management And Configuration Manual

The HP Aruba 2930F Series is a high-performance networking solution designed to meet the demands of modern businesses. It offers advanced management and configuration capabilities, ensuring seamless integration into your network infrastructure. Download the comprehensive Management and Configuration Manual for free from manualshive.com to learn more about harnessing the full potential of this powerful product.

Share
Download
background image

VSF split

A VSF split can occur due to a VSF link failure where all ports in the VSF link go down or any member is power-
cycled or crashes in the chain topology. This failure results in independent VSF fabric fragment each having its
own Commander role. It is recommended to configure a Multiple Active Detection (MAD) mechanism to avoid
duplicate IP addresses, routing issues and traffic forwarding problems when a VSF split occurs.

Figure 107: VSF split

Commander

+

Member 1

Member 2

Standby

Commander

+

Standby

Commander

Standby

Commander

Member 1

Standby

Member 2

In the preceding figure, after the split, Member 1 will be elected as the new Standby in the previous Commander
fragment. Previous Standby will failover and become Commander. Member 2 will be elected as a new standby to
that fragment. Once the fragment become inactive, all front plane ports except VSF links will be brought down. A
limited set of CLI commands will be available on the inactive fragment.

VSF merge

VSF merge occurs on connecting two different VSF fragments having the same domain-ID through VSF links.
One of the VSF fragments reboots to merge with the other fragment and forms one VSF fabric. Devices merge
only if they have the same domain ID.

Figure 108: VSF Merge

Commander

+

Standby

Standby

Commander

Commander

Standby

Member

Member

NOTE: 

Only two fragments can be merged at a time.

VSF commands

Configuration commands

Chapter 20 Virtual Switching Framework (VSF)

655

Summary of Contents for Aruba 2930F Series








































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Aruba 2930F Series

Zektor CVS4 User Manual Supplement preview
CVS4
Brand: Zektor Pages: 17
IBM 8237 Installation And User Manual preview
8237
Brand: IBM Pages: 166
Blackmagicdesign Universal Videohub 288 Installation And Operation Manual preview
Universal Videohub 288
Brand: Blackmagicdesign Pages: 107
Radio Systems HUB16-DC Technical Manual preview
HUB16-DC
Brand: Radio Systems Pages: 19
3onedata IES2008 Quick Installation Manual preview
IES2008
Brand: 3onedata Pages: 2
Articona 386428 Quick Installation Manual preview
386428
Brand: Articona Pages: 2
SMART-AVI DVN-8P Installation Manual preview
DVN-8P
Brand: SMART-AVI Pages: 2
Black Box SW421A-R2 Specifications preview
SW421A-R2
Brand: Black Box Pages: 2
LEGRAND Valena Life LE-752107 User Manual preview
Valena Life LE-752107
Brand: LEGRAND Pages: 5
MCOHome MH-S312 User Manual preview
MH-S312
Brand: MCOHome Pages: 3
BJ Live BJ-277 User Manual preview
BJ-277
Brand: BJ Live Pages: 2
asas Motoroll Manual preview
Motoroll
Brand: asas Pages: 25
Samson 4746 Mounting And Operating Instructions preview
4746
Brand: Samson Pages: 40
3Com 3C16470 User Manual preview
3C16470
Brand: 3Com Pages: 8
3Com 3C16751 User Manual preview
3C16751
Brand: 3Com Pages: 8
Rose electronics ServeView Pro Installation And Operation Manual preview
ServeView Pro
Brand: Rose electronics Pages: 36
MyRepublic WI-FI HUB+ Troubleshooting Manual preview
WI-FI HUB+
Brand: MyRepublic Pages: 7
JVC JX-B555 Instructions Manual preview
JX-B555
Brand: JVC Pages: 29

Brands by name

Popular brands

Load more brands