HP A7500 Series Command Reference Manual Download Page 205 | Manualshive

Page: 205 / 222

background image

198

CAUTION:

•

A reboot can interrupt network services.

•

Adjusting the system time setting can cause removal of the reboot schedule.

Examples

# Configure the switch to reboot in 88 minutes. This example assumes that the current time is 11:48.

<Sysname> schedule reboot delay 88

Reboot system at 13:16 06/06/2006(in 1 hour(s) and 28 minute(s)). confirm? [Y/N]:

Enter

y

at the prompt. If you have used the

terminal logging

command to enable the log display function

(enabled by default) on the terminal, the system automatically displays a reboot schedule log message.

<Sysname>

%Jun 6 11:48:44:860 2006 Sysname CMD/4/REBOOT:

vty0(192.168.1.54): Set schedule reboot parameters at 11:48:44 06/06/2006, and system will

reboot at 13:16 06/06/2006.

shutdown-interval

Syntax

shutdown-interval

time

undo shutdown-interval

View

System view

Default level

2: System level

Parameters

time

: Detection interval in seconds, which ranges from 0 to 300.

Description

Use the

shutdown-interval

command to set a detection interval.

Use the

undo

shutdown-interval

command to restore the default.

By default, the detection interval is 30 seconds.
Some protocols might shut down ports under specific circumstances. For example, MSTP shuts down a

BPDU guard enabled port when the port receives a BPDU. Then, the switch starts the detection timer. If

the port is still down when the detection timer expires, the switch automatically brings up the port.

•

If you change the detection interval to T1 during port detection, the interval from when you change
the interval to the time when the protocol module shuts down the port is T. If T<T1, the port which is

down will be brought up after T1-T time. If T>=T1, the port which is down will be brought up

immediately. For example, if the detection interval is set to 30 seconds and you change it to 10
seconds (T1=10) two seconds after the port is shut down (T=2), this port will be brought up 8

seconds later. If the detection interval is set to 30 seconds and you change it to 2 seconds ten

seconds after the port is shut down, this port will be brought up immediately.

•

If the detection interval is set to 0, the protocol module will never automatically recover the port. You
need to manually bring up the port by using the

undo shutdown

command or change the detection

interval to a non-zero value.

«
...
203
204
205
206
207
...
»

Summary of Contents for A7500 Series































































































































































































































Reviews:

No comments

Related manuals for A7500 Series

Underwater Switch 24V DC/DMX/02

Brand: Oase Pages: 40

Brand: AVE Pages: 2

Infinity IES-1881

Brand: LevelOne Pages: 2

Brand: XtendLan Pages: 24

Brand: Grozone Control Pages: 20

Brand: Black Box Pages: 74

Brand: Guntermann & Drunck Pages: 20

Brand: Hama Pages: 14

Brand: Inline Pages: 4

Brand: Parallax Power Supply Pages: 2

Brand: TP-Link Pages: 2

Brand: Abtus Pages: 2

Brand: Led Control Pages: 22

Comfy LW920 Professional Series

Brand: LightwaveRF Pages: 41

Brand: Brocade Communications Systems Pages: 54

Brand: AJAX Pages: 23

Elinx EIRP305-T

Brand: B&B Electronics Pages: 2

Brand: Ross Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands