manualshive.com logo in svg

HP A5120 EI Series, Installation Manual, Page: 77 / 91

Share
Download
HP A5120 EI Series Installation Manual Download Page 77

 

72 

Combo interface (only available on the A5120 EI switches)  

On  an  A5120  EI  switch,  the  last  four  10/100/1000Base-T  Ethernet  ports  and  the  four  SFP  ports  are 
copper/fiber combo ports in pairs, as shown in 

Table 16

. They form four combo interfaces. When one 

port in a pair is activated, the other port automatically shuts down. For more information about combo 
interfaces, see "

HP A5120 EI Switch Series Configuration Guides

." 

Table 16

 

Copper/fiber combo ports in pairs 

Chassis

 

SFP port

 

10/100/1000Base-T Ethernet 

port

 

A5120-24G EI (2 slots) 
A5120-24G EI TAA (2 slots) 
A5120-24G-PoE+ EI (2 slots) 
A5120-24G-PoE+ EI TAA (2 slots) 
A5120-24G EI 

GigabitEthernet 1/0/25 

GigabitEthernet 1/0/22 

GigabitEthernet 1/0/26 

GigabitEthernet 1/0/24 

GigabitEthernet 1/0/27 

GigabitEthernet 1/0/21 

GigabitEthernet 1/0/28 

GigabitEthernet 1/0/23 

A5120-48G EI (2 slots) 
A5120-48G EI TAA (2 slots) 
A5120-48G-PoE+ EI (2 slots) 
A5120-48G-PoE+ EI TAA (2 slots) 
A5120-48G EI 

GigabitEthernet 1/0/49 

GigabitEthernet 1/0/46 

GigabitEthernet 1/0/50 

GigabitEthernet 1/0/48 

GigabitEthernet 1/0/51 

GigabitEthernet 1/0/45 

GigabitEthernet 1/0/52 

GigabitEthernet 1/0/47 

 

LEDs (for the A5120 EI switches)  

Table 17

 

LEDs at a glance 

LED 

Availability 

System status LED 

Entire series 

RPS status LED  

Entire series 

Port mode LED 

Entire series 

Seven-segment LED 

Entire series 

10/100/1000 Base-T Ethernet port LED 

Entire series 

SFP port LED 

Entire series 

Interface card status LED 

Entire series (except the A5120-24G EI and A5120-48G EI) 

 

System status LED 

The system status LED shows the operating status of the switch. 

Table 18

 

System status LED description 

LED mark 

Status 

Description 

PWR 

Steady green 

The switch is operating properly. 

Summary of Contents for A5120 EI Series




























































































Reviews:

No comments