manualshive.com logo in svg

HP A5120 EI Series, Installation Manual, Page: 80 / 91

Share
Download
HP A5120 EI Series Installation Manual Download Page 80

 

75 

Table 23

 

Seven-segment LED description (II) 

Port mode LED 

(Mode) status 

System status LED 

(PWR) status 

Seven-segment 

LED (Unit) status   Description 

Flashing green (1 
Hz) (PoE mode) 

Steady green 

The LED displays 
different signs. 

 

0 - 20% 

21 - 40% 

41 - 60% 

61 - 80% 

81 - 100% 

 

For example, the 

 

 sign indicates that 

the switch is outputting 0 to 20% of the 
maximum PoE output power.  

 

10/100/1000 Base-T Ethernet port LED    

Each 10/100/1000Base-T auto-sensing Ethernet port has a status LED to show port operating status and 
activities. The port mode LED indicates the type of information (for example, port rate or duplex mode) 
that the port LEDs are showing. You can use the port LED mode switching button to change the type of 
port information that is displayed. 

Table 24

 

10/100/1000Base-T auto-sensing Ethernet port LEDs description 

Port mode LED (Mode) 

status 

Port LED status 

Description 

Steady green (rate mode) 

Steady green 

The port is operating at 1000 Mbps. The port LED 
fast flashes when the port is sending or receiving 
data. 

Steady yellow 

The port is operating at 10/100 Mbps. The port 
LED fast flashes when the port is sending or 
receiving data. 

Flashing yellow (3 Hz) 

POST has failed on the port. 

Off 

No link is present on the port. 

Flashing green (1 Hz) 
(PoE mode, available 
only for PoE switches) 

Steady green 

PoE power supply is normal. 

Flashing green (1 Hz) 

The device attached to the port requires power 
higher than the maximum or currently available 
PoE output power on the port. 

Steady yellow 

The port is experiencing a PoE failure.  
The port is not supplying power, because the 
device attached to the port is not a powered 
device. 

Flashing yellow (3 Hz) 

POST has failed on the port. 

Off 

The port is not supplying PoE power. 

Steady yellow (duplex 
mode) 

Steady green 

The port is operating in full duplex mode. The port 
LED fast flashes when the port is sending or 
receiving data. 

Steady yellow 

The port is operating in half duplex mode. The 
port LED fast flashes when the port is sending or 
receiving data. 

Flashing yellow (3 Hz) 

POST has failed on the port. 

Off 

No link is present on the port. 

 

Summary of Contents for A5120 EI Series




























































































Reviews:

No comments