HP 8920A User Manual Download Page 568 | Manualshive

Page: 568 / 658

background image

568

S:\HP892XX\USRGUIDE\manual\connkeys.fb

Chapter 24, Connector, Key, and Knob Descriptions

Connector Descriptions

HP-IB

This connector is optional on the HP 8920A.

This connector allows communication between the Test Set and other instruments
or computers using the Hewlett-Packard Interface Bus (HP-IB).

See Also

Chapter 12, "I/O Configure Screen"

HP 8920 Programmer’s Guide

MEMORY CARD Slot

This front-panel opening is where memory cards are inserted.

See Also

HP 8920 Programmer’s Guide

MIC/ACC

This 8-pin DIN connector (see

figure 146 on page 570

) is used for several

functions:

•

Mic In is used to modulate the RF Generator when the KEY IN line is grounded. This
signal is summed with the external MODULATION INPUT signal. The

Mod In To

field of the RF GENERATOR screen sets the type of modulation (AM or FM) and sen-
sitivity (%AM/Vpk or kHz/Vpk) for this connection.

•

Key In provides control of the RF Generator’s output state (on or off) and automatic
switching between the TX TEST and RX TEST screens (if the CONFIGURE screen’s

RX/TX Cntl

functions are set to

Auto

and

PTT

). Screen switching occurs when this

line is grounded.

•

Key Out 1 and Key Out 2 provide a switch path to control external equipment (such as
keying a transmitter). Key Out 1 and Key Out 2 are connected when the

Ext TX key

field is set to

On

.

CAUTION:

Do not exceed 50 Vdc (open circuit) or 250 mA dc (closed circuit) between Key Out 1 and Key
Out 2. Damage to internal components may result.

«
...
566
567
568
569
570
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: GE Pages: 802

Brand: iET Pages: 17

Brand: Raven Pages: 27

Brand: Raven Pages: 79

Brand: Raven Pages: 88

Brand: HAMAR LASER Pages: 49

Brand: Bante Instruments Pages: 6

Brand: Cameo Pages: 64

Brand: Cameo Pages: 100

Brand: CAME Pages: 32

Brand: Gebhardt Anlagentechnik Pages: 152

Brand: Hach Pages: 58

Brand: Hach Pages: 52

Brand: Ransomes Pages: 282

Ransomes HR 6010

Brand: Jacobsen Pages: 10

Brand: Jacto Pages: 64

Brand: Labelmate Pages: 61

Brand: Labconco Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands