manualshive.com logo in svg

HP 85106D, Manual

Share
Download
HP 85106D Manual Download Page 192

HP 85106D mm-Wave System

6-27

HP 85105A mm-Wave Controller

Self-Test Indicators

The ACTIVE LED should always remain off until the HP 85105A is
accessed by the HP 8510. Each time the test set is turned on the Port 1 and
Port 2 LEDs will light for approximately 2 seconds during the self-test, and
then turn off. To determine what part of the self-test has failed, note which
LEDs on the A4 board are lit. Refer to Table 6-3 for failure indications.

If the Self-test Fails to
Run

If the portion of memory which contains the self-test programming is faulty,
the self-test will not run properly. The following conditions indicate that the
self-test ROMs are probably faulty.

•

all LEDs flash briefly and go off

•

all LEDs flash briefly and stay on

•

ACTIVE LED goes on too soon

Table 6-3

Self-Test Failure Indications

Self-Test Indication

A4 HP-IB LED’s

Time (after turn-on)

LSN

TLK

SRQ

REM

PWON

ON

ON

ON

ON

0 to 0.5 sec

Fail  ROM  Test

OFF

ON

ON

ON

ON  briefly

Pass ROM Test

OFF

OFFF

ON

ON

0.5 to 2.0 sec

Fail RAM Test

OFF

OFF

OFF

ON

Pass RAM Test

OFF

OFF

OFF

OFF

after 2 sec

Summary of Contents for 85106D





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands