HP 669048-009 Installation Manual Download Page 103 | Manualshive

Page: 103 / 108

background image

Support and other resources 103

Support and other resources

Before you contact HP

Be sure to have the following information available before you call HP:

•

Active Health System log (HP ProLiant Gen8 or later products)
Download and have available an Active Health System log for 7 days before the failure was detected.
For more information, see the

HP iLO 4 User Guide

or

HP Intelligent Provisioning User Guide

on the HP

website (

http://www.hp.com/go/ilo/docs

•

Onboard Administrator SHOW ALL report (for HP BladeSystem products only)
For more information on obtaining the Onboard Administrator SHOW ALL report, see the HP website
(

http://www.hp.com/go/OAlog

•

Technical support registration number (if applicable)

•

Product serial number

•

Product model name and number

•

Product identification number

•

Applicable error messages

•

Add-on boards or hardware

•

Third-party hardware or software

•

Operating system type and revision level

HP contact information

For United States and worldwide contact information, see the Contact HP website

http://www.hp.com/go/assistance

In the United States:

•

To contact HP by phone, call 1-800-334-5144. For continuous quality improvement, calls may be
recorded or monitored.

•

If you have purchased a Care Pack (service upgrade), see the Support & Drivers website
(

http://www8.hp.com/us/en/support-drivers.html

). If the problem cannot be resolved at the website,

call 1-800-633-3600. For more information about Care Packs, see the HP website
(

http://pro-aq-sama.houston.hp.com/services/cache/10950-0-0-225-121.html

«
...
101
102
103
104
105
...
»

Summary of Contents for 669048-009













































































































Reviews:

No comments

Related manuals for 669048-009

Brand: HAGOR Pages: 16

Santa Fe II Easel

Brand: Jack Richeson Pages: 2

ScreenOut OH 46

Brand: HAGOR Pages: 24

COMFORT 1800 FLOOR STAND

Brand: Silverline Pages: 8

Brand: ADDER Pages: 2

FIREWOOD RACK-IN-A-BOX

Brand: ShelterLogic Pages: 5

Brand: B-Tech Pages: 24

Counter Basic Mount

Brand: lilitab Pages: 8

Mainmast DMS-200

Brand: GABOR Pages: 12

Fiber Pedlock BDO2 Series

Brand: Charles Pages: 22

Brand: Woom Pages: 2

Brand: Nanit Pages: 52

Brand: Yealink Pages: 8

Charisma SEG XSS Custom Adjustable Series

Brand: Testrite Visual Pages: 2

Brand: Body Solid Pages: 16

Brand: Crestron Pages: 12

Brand: Tripp Lite Pages: 56

Brand: arkitect Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands