manualshive.com logo in svg

HP 5500 EI series, Configuration Manual, Page: 21 / 424

Share
Download
HP 5500 EI series Configuration Manual Download Page 21

 

10 

Configuring static route FRR 

A link or router failure on a path can cause packet loss and even routing loop. Static route fast reroute 
(FRR) enables fast rerouting to minimize the impact of link or node failures. 

Figure 1

 

Network diagram 

 

 

As shown in 

Figure 1

, upon a link failure, FRR specifies a backup next hop by using a routing policy for 

routes matching the specified criteria. Packets are directed to the backup next hop to avoid traffic 

interruption. 

Configuration guidelines 

•

 

Do not use static route FRR and BFD (for a static route) at the same time. 

•

 

Static route does not take effect when the backup output interface is unavailable. 

•

 

Equal-cost routes do not support static route FRR. 

•

 

The backup output interface and next hop cannot be modified directly or the same as the primary 
output interface and next hop. 

•

 

Static route FRR is available only when the state of primary link (with Layer 3 interfaces staying up) 
changes from bidirectional to unidirectional or down. A unidirectional link refers to the link through 

which packets are forwarded only from one end to the other. 

Configuration procedure 

To configure static route FRR: 

 

Step Command 

Remarks 

1.

 

Enter system view. 

system-view 

N/A

 

2.

 

Configure the source 
address of BFD echo 

packets. 

bfd echo-source-ip

 

ip-address

 

By default, the source address 
of BFD echo packets is not 
configured. 
For more information about 
this command, see 

High 

Availability Command 

Reference

. 

Summary of Contents for 5500 EI series









































































































































































































































































































































































































































Reviews:

No comments