HP 3100 v2 Series Command Reference Manual Download Page 51

Page: 51 / 239

Related commands:

interface null

Examples

# Display detailed information about null interface Null 0.

<Sysname> display interface null 0

NULL0 current state :UP

Line protocol current state :UP (spoofing)

Description : NULL0 Interface

The Maximum Transmit Unit is 1500

Internet protocol processing : disabled

Physical is NULL DEV

Port priority: 0

Last clearing of counters: Never

Last 300 seconds input: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output: 0 bytes/sec, 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 drops

0 packets output, 0 bytes, 0 drops

# Display brief information about interface Null 0.

<Sysname> display interface null 0 brief

The brief information of interface(s) under route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface Link Protocol Main IP Description

NULL0 UP UP(s) --

For the output description, see

Table 10

NOTE:

The switch does not support collecting statistics about average input or output rate of interface Null
0. These fields display

interface loopback

Syntax

interface loopback

undo interface loopback

View

System view

Default level

2: System level

Parameters

: Loopback interface number

Description

Use

interface loopback

to create a loopback interface or enter loopback interface view.

Use

undo interface loopback

to remove a loopback interface.

Related commands:

display interface loopback

Summary of Contents for 3100 v2 Series
















































































































































































































































Search results

Summary of Contents for 3100 v2 Series

Reviews:

Related manuals for 3100 v2 Series

Brands by name

Popular brands

HP 3100 v2 Series, Command Reference Manual

Search results

Summary of Contents for 3100 v2 Series

Reviews:

Related manuals for 3100 v2 Series

Brands by name

Popular brands