manualshive.com logo in svg

HP 3100 v2 Series, Command Reference Manual

Share
Download
HP 3100 v2 Series Command Reference Manual Download Page 48

 

41 

|

: Filters command output by specifying a regular expression. For more information about regular 

expressions, see 

Fundamentals Configuration Guide

. 

begin

: Displays the first line that matches the specified regular expression and all lines that follow. 

exclude

: Displays all lines that do not match the specified regular expression. 

include

: Displays all lines that match the specified regular expression. 

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters. 

Description 

Use 

display interface loopback 

to display information about a loopback interface. 

•

 

If you do not specify the 

loopback

 keyword, this command displays information about all 

interfaces on the device. 

•

 

The device supports only one loopback interface, loopback 0, and therefore this command 
displays information about loopback 0 whether you specify 

loopback

 or 

loopback 0

. 

Related commands: 

interface loopback

. 

Examples 

# Display detailed information about interface loopback 0. 

<Sysname> display interface loopback 0 

LoopBack0 current state: UP 

Line protocol current state: UP (spoofing) 

Description: LoopBack0 Interface 

The Maximum Transmit Unit is 1536 

Internet protocol processing : disabled 

Physical is Loopback 

Port priority: 0 

Last clearing of counters:  Never 

    Last 300 seconds input:  0 bytes/sec, 0 bits/sec, 0 packets/sec 

    Last 300 seconds output:  0 bytes/sec, 0 bits/sec, 0 packets/sec 

    0 packets input, 0 bytes, 0 drops 

    0 packets output, 0 bytes, 0 drops 

# Display brief information about interface loopback 0. 

<Sysname> display interface loopback 0 brief 

The brief information of interface(s) under route mode: 

Link: ADM - administratively down; Stby - standby 

Protocol: (s) - spoofing 

Interface            Link Protocol Main IP         Description 

Loop0                UP   UP(s)    -- 

Table 10 Command output 

Field Description 

current state 

Physical state (up or administratively down) of the interface. 

Line protocol current state 

State of the data link layer protocol: up (spoofing). Spoofing 
refers to the spoofing attribute of the interface. When the 
network layer protocol state of the interface is displayed as up, 
the corresponding link may not exist, or the corresponding link is 
non-permanent and established on demand. 

Description 

Description string of the interface. 

The Maximum Transmit Unit 

Maximum transmission unit (MTU) of the interface. 

Summary of Contents for 3100 v2 Series
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands