Hozelock Aquaforce 1000 Instruction Manual Download Page 2

INTRODUCTION

The pump is electrically operated and is designed to pump
solid particles up to 6mm in diameter with minimal pre-
strainer maintenance.

These types of pumps are particularly suitable for pumping
water to external filters or for use in high flow waterfalls
or watercourse applications where low maintenance is
important. The pump does not use oil or grease for
lubrication and can be used safely in ponds containing fish
or plants. The motor consists of a sealed stator and water-
cooled rotor. All electrical components are isolated from
the water.

ATTENTION

AUTOMATIC CUT-OUT 

To help ensure your pump’s long life and to prevent
damage, it is fitted with automatic thermal overload
protection. This switches off the pump if it overheats. If
this occurs, switch off the power at the mains supply to
the pump. Check for the cause. Usually it will be debris

blocking the inlets of the pump or obstructing the
impeller. Remove the obstruction and wait for the pump
to cool down. Then switch on the pump again.

NOTE (AQUAFORCE 2500 & 4000): YOU MUST SWITCH
OFF THE MAINS SUPPLY BEFORE THE PUMP WILL RESET.

GENERAL SAFETY GUIDELINES

Failure to observe the following notices may result in
injury, product damage or loss of fish.

1. This pump has been designed for the use with ponds

only. Only use this pump for the operation of pond
filter systems, water displays, waterfalls etc. Do not use
this pump for any other use (i.e. do not use this pump
in swimming pools, bathrooms, central heating systems
etc). Using the product for any other application may
result in injury or product damage.

2. This appliance is not intended for use by persons

(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person

A. Wildlife Protection system

B. Hosetail & Nut

C. Ball Joint

D. Outlet adaptor

E. Pump

F. Filter Cage

G. Pump cradle (Aquaforce 1000

only)

Fig. 1
1000

Fig. 2
2500 + 4000

A

B

D

C

E

F

G

A

B

D

C

E

F

Summary of Contents for Aquaforce 1000









Reviews: