background image

Safety Tips:

•Ensure that the cabinet is positioned square and firm on the floor so that it will not fall

over. Some cabinets are equipped with adjustable floor levelers. Adjust the levelers for
maximum stability and proper alignment. (The levelers may have unscrewed unevenly
during shipment.)

•Some cabinets include a Safety Strap. Follow the instructions included with the Safety

Strap to ensure maximum stability. (See step #5)

•Keep plastic bags and small parts away from children.
•Cabinets may be lit using a halogen lamp. Halogen lamps operate at high temperatures.

Combustible materials or those adversely affected by drying or fading from the heat
should not be placed close to the lamp.

Care of Glass Shelves:

•To prevent breakage of glass shelves and collectibles, good judgement must be used

during the installation and loading of glass shelves. 

Heavy loads on the shelves must

be distributed and must not exceed 25 pounds.

•Glass shelves must be properly installed onto the shelf supports provided and should not

be overloaded. (Figure 8 & 9)

•Care should be taken when placing items onto each glass shelf. Sudden shock from any

size item can result in broken glass, personal injury, or damage to valuable items.

•The end use of this cabinet is beyond our control and therefore, the Howard Miller

Company cannot assume responsibility for broken glass or personal effects.

Cabinet Set Up

1. Inspect the inside of carton and packaging to make sure you have removed all separately

packed parts, including shelves, shelf supports, door lock key, No-Reach™ or Touch-
Lite™ assembly. 

2. Locate the package of glass shelves. The shelves may be located:

a) Inside your cabinet and secured with shipping clips. To remove the shipping clips, you

will need a Phillips screwdriver. (Figure 1) 

b) On top, underneath, or along side of your cabinet. You may need to lay the cabinet on

it’s backside to remove the shelves from underneath the cabinet. Use caution when
removing these shelves.

3. If available on your cabinet, turn the adjustable floor levelers, that are on the bottom of the

cabinet, all the  way in (up). (Figure 2)

4. Identify one of the following light switch options provided with your cabinet and install as directed

.

No-Reach™ Light Switch: Installation

Locate the light On/Off switch. Insert the switch inside the plastic bracket by
pressing the electrical cord wires into each slot. Peel away the adhesive paper
from the backside of the bracket and press firmly to the backside of the cabinet
in the desired location. (Figure 3)

Touch-Lite™ Pad: Installation 

a) Remove the Dimmer Block, Power Cord and Sensor Wire from the plastic bag,

usually located on top of the cabinet. (Figure 4)

b) The Touch Pad Key Holder Assembly is located in a plastic bag with the shelf clips. 
c) Attach the Touch Pad Key Holder Assembly to the end of the Sensor Wire.

(Figure 5) Use care to avoid bending as damage may occur if this is forced on.

d) Peel away the adhesive paper from the backside of the Dimmer Block. Press

the Dimmer Block firmly to the top of the dust panel or to the backside of the
cabinet to allow convenient access to both the power source and the Touch
Pad Key Holder. (Figure 6)

e) Peel away the adhesive paper from the backside of the Touch Pad Key Holder

Assembly. Verify that the Key Holder is to the bottom and the attachment to
the Sensor Wire is at the top. Press the Touch Pad firmly to the backside of the
cabinet at the desired location. (Figure 7)

Touch-Lite™ Pad: Operation

The light begins in the off position. The operation is
sequential and will advance to the next Light Illumination
Level with each subsequent touch to the Touch Pad. 

1st touch = Low Light Illumination Level
2nd touch = Medium Light Illumination Level
3rd touch = High Light Illumination Level
4th touch = turns light off 

CABINET INSTRUCTIONS

FIGURE 2

FIGURA 2

FIGURE 2

ABBILDUNG 2

FIGURE 1

FIGURA 1

FIGURE 1

ABBILDUNG 1

Shipping Clip

Ajuste del sujetador

Attache de transport

Transportklemme

Leveler

Nivelador

Patin de réglage

Nivellierfuß

FIGURE 7

FIGURA 7

FIGURE 7

ABBILDUNG 7

FIGURE 4

FIGURA 4

FIGURE 4

ABBILDUNG 4

FIGURE 3

FIGURA 3

FIGURE 3

ABBILDUNG 3

FIGURE 5

FIGURA 5

FIGURE 5

ABBILDUNG 5

Plastic Bracket

Soporte plástico

Patte en plastique

Kunststoffhalterung

On/Off Switch

Interruptor para apagado y encendido

Interrupteur de marche et arrêt

Ein/Aus-Schalter

Key Holder 

Portalámpara de llave

Support de clé

Schlüsselhalter

Touch-Lite™ Pad

Almohadilla Touch-Lite™

Touche à effleurement

Touch-Lite Pad

Sensor Wire

Alambre sensor

Fil capteur

Sensordraht

Power Cord

Cable de alimentación eléctrica

Cordon d'alimentation

Netzkabel

Dimmer Block

Interruptor de graduación de luz

Bloc gradateur

Dimmer-Einsatz

Touch Pad Key Holder Assembly
Portalámpara de llave del controlador de tacto
Assemblage touche à effleurement/support de clé
Touch-Pad/Schlüsselhalter-Bausatz

Sensor Wire

Alambre sensor

Fil capteur

Sensordraht

Sensor Wire
Alambre sensor
Fil capteur
Sensordraht

Touch Pad
Controlador de tacto
Touche à effleurement
Touch-Pad

Key Holder 
Portalámpara de llave
Support de clé
Schlüsselhalter

No-Reach™ Light Switch

Interruptor para lámpara No-Reach™

Interrupteur de lampe No-Reach

No-Reach Lichtschalter

FIGURE 6

FIGURA 6

FIGURE 6

ABBILDUNG 6

Dimmer Block

Interruptor de graduación de luz

Bloc gradateur

Dimmer-Einsatz

Summary of Contents for Curio Cabinet

Page 1: ... the Dimmer Block Power Cord and Sensor Wire from the plastic bag usually located on top of the cabinet Figure 4 b The Touch Pad Key Holder Assembly is located in a plastic bag with the shelf clips c Attach the Touch Pad Key Holder Assembly to the end of the Sensor Wire Figure 5 Use care to avoid bending as damage may occur if this is forced on d Peel away the adhesive paper from the backside of t...

Page 2: ...ce the shelf supports into the desired holes inside the cabinet Figure 8 9 There are several holes that can be used for shelf height adjustment b Install shelves Starting at the bottom and working upward place each shelf onto the shelf supports Figure 8 9 Note Some cabinets may have a wood rail which is intended to support a glass shelf This wood rail will have a no slide pad for the glass shelf t...

Page 3: ...de a nivel en ambos sentidos y repose en forma perpendicular y con firmeza sobre el piso Sólo se requerirá el uso del nivel durante este paso INSTRUCTIONS POUR L ARMOIRE DE COLLECTIONNEUR Conseils de sécurité Assurez vous que l armoire de collectionneur est placée bien droit et fermement sur le plancher de sorte qu elle ne renverse pas Ajustez les boutons de réglage de la hauteur pour obtenir une ...

Page 4: ...el número de modelo y el número de serie los cuales se pueden encontrar en la Etiqueta de Información del Producto que por lo general se encuentra en el lado inferior del gabinete Número de Modelo _______________ Número de Serie ______________________ Fecha de Compra ________________ Lugar de Compra ________________________ Breve Descripción del Problema __________________________________________ ...

Reviews: