Hover-1 FALCON-1 Operation Manual Download Page 18

The first rule of safe riding is to use common sense. The Falcon-1 cannot protect you in a crash, against 

impact, or from loss of control the way a car can. The Falcon-1 can tip over sideways or pitch you over the 

front wheel if you don’t ride it properly. Please read the following safety precautions to operate your Falcon-1 

safely. 

Different localities and countries have different laws governing riding on public roads, and you should check 

with local officials to ensure you are complying with these laws. 

Hover-1 is not liable for tickets or violations given to riders who do not follow these regulations.

• For your safety, always wear a helmet that meets CPSC or CE safety standards. In the event of an accident, 

a helmet can protect you from serious injury and in some cases, even death. 

• Obey all local laws, stop signs, pedestrian crosswalks, etc.

• If you are riding with other riders, maintain a safe distance between each other to avoid collisions.

• Ride defensively; expect the unexpected.

• Give pedestrians the right-of-way.

• Do not ride too close to pedestrians. Alert them if you intend to pass them from behind.

• Slow down at all street intersections and look to the left and right before crossing.

•Obey all traffic signals.

• Always use proper hand signals for turning and stopping. Give signals 100 ft before stopping or turning and 

always return both hands to the handlebars before stopping or turning.

• Watch for cars when pulling into traffic and watch for the sudden opening of car doors.

• Avoid potholes, drainage grates, and other hazards.

• Be careful when riding on soft road edges, gravel, sand, and uneven surfaces. Ride slowly and avoid quick 

turns when riding on these surfaces.

• Never hitch onto other vehicles.

• Do not attempt any stunts or tricks with the Falcon-1. Do not race in traffic. 

• Do not weave in and out of traffic or swerve from side to side.

• A crash can put extraordinary stress on Falcon-1’s components, possibly causing them to fatigue 

prematurely. Components suffering from stress fatigue can fail suddenly, causing loss of control or 

serious injury.

CAUTION: RIDING IN WET WEATHER

It is recommended that you do not ride your Falcon-1 in wet weather, as the electronic components of the 

hoverboard may be damaged if exposed to water. Stopping distances will be longer in wet conditions.

1. This product is strictly forbidden to be used on roads and highways unless your local laws state otherwise. 

You must wear a safety helmet, knee and elbow pads, and other necessary protective gear when riding your 

Falcon-1.

2. Due to the nature of this product, the assembly pieces should be checked before every ride to avoid an 

accident while riding.

3. Do not make sharp turns, as you may drift and overturn the Falcon-1, which can result in injury to yourself 

and/or damage the unit.

4. Do not operate near swimming pools or other bodies of water.

 

WARNING

To reduce the risk of injury, adult supervision is required.

Never use in roadways, near motor vehicles, on or near 

steep inclines or steps, near swimming pools or other 

bodies of water. Always wear shoes, and never allow 

more than one rider at a time.

17

Summary of Contents for FALCON-1






















Reviews: