- 7 -
TEMPERATURE & DURATION CHART
Approx. Avg. Temp. Range
Duration Range
Set. °C
°F
Power Plus
m4
Power Plus
m3
1
28°-32°
83°-89°
19-21 hrs
15-17 hrs
2
36°-41°
96°-106°
7-9 hrs
5.5-7 hrs
3
40°-47°
105°-116°
5-6.5 hrs
3.5-5 hrs
4
57°-62°
135°-144°
2.5-3.75 hrs
2-3 hrs
OPERATING BATTERY PACK SETTINGS
1.
To turn on or off
, press-and-hold ON or OFF until LED light is ON
or OFF (~2.0 seconds).
2.
To change setting
, press-and-hold
◄
or
►
until setting LED light
changes (~0.5 seconds).
3.
Once selected, setting 4 auto-resets to setting 3 after 3 minutes
(“timed setting 4”). (“Timed setting 4” LED lights are ON
continuously and do NOT blink.)
4.
To use “continuous setting 4”
, start at “timed setting 4”, then press
and hold
►
until all LED lights blink (~5.0 seconds). (“Continuous
setting 4” LED lights BLINK continuously until setting is changed.)
5.
DO NOT USE “TIMED SETTING 4” or ”CONTINUOUS SETTING
4”
for more than three minutes at a time as it may become too hot
and may result in burns.
SEE CAUTIONS REGARDING BURNS
.
BATTERY PACK LED LIGHTS (LEDs)
1.
Battery Pack LEDs
indicate power is on or off and setting selected
.
LEDs do not indicate charge level.
2.
LEDs will not light
when batteries are fully discharged, are below
minimum voltage cutoff level, or do not have enough power to heat
Element.
EXCESS HEAT ON ANY SETTING, INCLUDING OFF
1.
WHEN BATTERY PACK LED stays ON and CANNOT BE TURNED
OFF
, water may be around electrical contacts, may cause Heating
Element to become hot at any setting, and
MAY RESULT IN BURNS
.
See CAUTIONS REGARDING BURNS.
2.
WHEN BATTERY PACK IS ON ANY SETTING, INCLUDING OFF,
and you feel your foot getting hot, you think you might be getting a
burn, or you experience any early warning sensations of a burn,
IMMEDIATELY UNPLUG
Heating Element from Battery Pack and
IMMEDIATELY REMOVE
your foot from FootWarmer.
See
CAUTIONS REGARDING BURNS.
USING HEAT SETTINGS
1.
Use FootWarmer to
maintain comfort and warmth
. (
Note:
Prevent
feet from getting cold. Warming cold feet requires more energy, is
less effective, and is not intended use of FootWarmer.)
2.
Before going into cold,
set at 1, 2, or 3 to maintain comfort and
warmth.
3.
For additional burst of heat, set to “timed setting 4”.
“Timed setting
4” auto-resets to setting 3 after 3 minutes.
4.
DO NOT USE “TIMED SETTING 4” or ”CONTINUOUS SETTING
4”
for more than three minutes at a time as it may become too hot
and may result in burns.
SEE CAUTIONS REGARDING BURNS
.
5.
Heat does not thermostatically cycle on and off
. Settings 1 and 2
maintain warmth AND save energy.
WHAT TO EXPECT OF HEAT SETTINGS
1.
Expect imperceptible heat
to maintain comfort and warmth.
2.
Do not expect “
fireplace toes”.
3.
Learn
what personally works best
over time.
4.
Think of your FootWarmer as
Thermo Active Insulation
(TM). As
cold penetrates through insole, it draws heat off Element rather than
toes.
Balanced heat
is imperceptible yet maintains comfort and
Summary of Contents for m3 power plus
Page 1: ... ...
