CAUTION
CAUTION
WARNING
CAUTION
The symbols below indicate what should be obeyed.
Disregarding this symbol may result in injury
or damage to equipment
Disregarding this symbol may result in
serious injury or death
This symbol refers to an
instructions which is prohibited
This symbol refer to an Instruction which must
be followed
This symbol refers to a Caution
WARNING
CAUTION
The symbols below indicate an extremely dangerous situation.
2. Remove Cover
User Manual
3H-IR14
Motion and Presence Sensor
We would like to extend our thanks to you for purchasing this product.
Before using this product, please read the following instructions carefully.
Please retain this manual for reference in case it needs to be referred to during the lifetime of this product.
2. MOUNTING PRECAUTIONS
To prevent leakage, malfunction or damage, please follow instructions below.
1. Mount lower than 3m (9.8ft)
2. Ensure no moving objects in the
detection area
4. Mount where rain or snow will not fall directly on unit.
1. Accumulation of
snow or water on the
floor.
3. Ensure the minimum of reflected
sunlight from the floor
2. Environment is
humid or steamy.
5. Please install in a place where no vibration
Cover
1. DESCRIPTION
User
Manual
Accessories
Mounting
Template
Cable
(2.5m)
Body
Potentiometer
(Sensitivity Volume)
Connector
LED Indicator
Area Mask
Detection Window
Dip Switch
Base
3.0m
9. Place Cover on sensor and clean the sensor.
Do not move Body when
attaching Cover.
8. House Connectors in the
space provided.
1. Determine the mounting
position of the device and
attach Mounting Template.
Drill mounting and wiring
holes.
3. MOUNTING & WIRING INFORMATION
Drilling may cause electric shock.
Be careful of hidden wires inside the door engine cover.
7. Set the following parameters
4. DIP SWITCH SETTINGS
6. Wiring to the door controller.
4. Install Base with Mounting
Screws.
6. ADJUSTING DETECTION PATTERN
5. Attach Body to Base.
3. Remove Mounting Screws and Body
from Base .
4. DIP SWITCH SETTINGS
5. APPLYING POWER
8. VERIFICATION OF OPERATION
Mounting Screws
(2 pcs.)
If the sensor is exposed to
excessive rain or snow install
with a Hotron weather cover
In the following cases, the sensor may detect without the presence of a person
3. Objects placed in the detection area.
4. Pets / Animals enter the detection area.
Presence Timer
The sensor will detect a stationary object only for the time set by the
Presence Timer. When it is set to
, the period is
in case of the 1st
and 2nd row, 2 s in case of the 3rd and 4th row.
Monitor Mode
Set to Snow in instances where false door activations can result from
blowing snow, leaves or rubbish close to the door detection area. It should
be noted that sensitivity to detecting pedestrians may also be reduced.
Quantity of Detection Rows
The number of rows of detection can be set to 4, 3, 2,1 depending on
detection area requirements.
Frequency
When more than two sensors are used in close proximity to each other,
select different frequency setting for each sensors to prevent interference.
( A + B + C + D = Maximum 4 sensors )
If you change the setting of the Dip switch when
the power is on, the sensor will be reset in
approx 6 s.
If you carry out the followings, please turn off the power.
If you carry out the followings when the power is turned on, the sensor will detect for the presence timer setting that you have set
Before turning on the power, please wire the door controller to the sensor.
No moving object
Power-on/
Reset
Presence detection
If there is a moving object in detection area after power-up / reset, the sensor will be in motion detection mode.
If there is no moving object in detection area after power-up / reset, the sensor will be in presence detection mode.
Moving object
Motion detection
7 s
No moving object
7 s
Remove
moving
object
Presence detection
Motion
Detection
2 s
7. ADJUSTING SENSITIVITY
The reset is the same as the Power-On.
Please set in a manner suitable for operation.
Self-Monitoring
When the sensor has malfunctioned, the Green/Red LED blinks alternately
and the relay output is relayed to the sensor.
Cable
Green N.C.
Yellow N.O.
White COM
Red
Black Power
Non Pole
Connector
Place or remove the
mat on the detection
area.
Adjust the angle of Body.
Adjust the width of the detection area.
Adjust the sensitivity.
Default Setting
Presence
Timer
2s
30s
60s
3 4
Frequency
A
B
C
D
5 6
Quantity of
Detection Rows
R4
R3
R2
R1
1 2
Monitor
Mode
Normal
7
1
2
3
4
5
6
7
8
Snow
Self-
Monitoring
OFF
8
ON
