10
GB
How to carry out
a drying cycle
Starting and selecting a programme
1.
Plug the dryer into the power supply socket.
2.
Select the programme according to the type of laundry
(see Laundry).
3.
Open the door, ensure that the filter is clean and securely placed and that the water container is empty and correctly slotted
(see
Care and maintenance).
4.
Load the machine, making sure that no piece of laundry gets between the door and the relative seal. Close the door.
5.
After consulting the programme chart and the indications for each type of fabric (
see Laundry
), turn the Programme selection
knob towards the programme corresponding to the type of laundry to be dried
(see Programmes and options).
!
;EVRMRK-JXLITSWMXMSRSJXLITVSKVEQQIWIPIGXMSRORSFGLERKIWEJXIVTVIWWMRKXLI78%684%97)FYXXSRXLIWIPIGXIHTVSKVEQ
-
QI[MPP238FIQSHMJMIH8SQSHMJ]XLITVSKVEQQITVIWWXLI78%684%97)FYXXSRXSTYXXLITVSKVEQQIMRTEYWIQSHIXLI
MRHMGEXSVPMKLXJPEWLIWSVERKIXLIRWIPIGXERI[TVSKVEQQIERHXLIVIPEXMZISTXMSRW4VIWWXLI78%684%97)FYXXSRXSWXEVXXLI
new programme.
6.
If necessary, set the time of the delayed start and any other options
(see Programmes and options).
7.
4VIWWXLI78%684%97)FYXXSRXSWXEVXXLIHV]MRKG]GPI
Laundry can be checked while the drying programme runs and any garments already dry can be removed, while drying continues
JSVXLIVIQEMRMRKMXIQW%JXIVGPSWMRKXLIHSSVTVIWWXLI78%684%97)FYXXSRXSVIWYQIQEGLMRISTIVEXMSR
8.
8LIJMREP'330891&0)TLEWIMIXLIJEFVMGWEVIGSSPIHEGXMZEXIWHYVMRKXLIPEWXJI[QMRYXIWSJXLIHV]MRKTVSKVEQQIEP[E]W
allow this phase to terminate.
9.
When the
END
indicator light turns on, the programme has ended. The buzzer will beep 3 times to let you know that your pro-
gramme is complete. Open the door, remove the laundry then clean the filter and replace it. Empty the water container and put it
back in its slot
(see Care and maintenance).
If the clothes are not removed at the end of the cycle the automatic
POST CREASE CARE
action will, on those programmes with
this feature, continue to rotate the drum intermittently for up to 10 hours to minimise creasing. The phase is stopped when the door
is opened or when the knob is set to OFF
10.
Set the program knob to OFF to switch off the machine.
11.
Disconnect the dryer from the power supply.
Automatic pre-post Crease Care
This is an automatic function which provides an anti crease treatment both before and after the drying programme. By periodically
rotating the drum before the start of the drying cycle, when a delayed start is selected, the formation of creases is prevented. On
certain programmes the drum also rotates periodically at the end of the drying cycle. The phase is stopped when the door is ope-
ned or when the knob is set to OFF.
Stand-by mode
This tumble dryer, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled
after about 30 minutes if no activity is detected.
8YVRXLIORSFXSXLIHIWMVIHTVSKVEQXSVIWXEVXHV]IVSTIVEXMSRXSWXEVXXLITVSKVEQTVIWW78%684%97)8LI3**TSWMXMSR
switches off the dryer.
