Hotpoint HR 612 CH Instructions For Use Manual Download Page 5

5

ELECTRICAL CONNECTIONS

Electrical connection must be made before connecting the appliance to the 

electricity supply. The appliance must be installed by a qualified electrician 

who is fully aware of current safety and installation regulations. Specifically, 

installation must be carried out in compliance with the regulations of the local 

electricity supply company. Make sure that the voltage shown on the rating 

plate is the same as the power supply voltage in your home. Regulations 

require that the appliance be earthed: use conductors (including the earth 

conductor) of the appropriate size only. The manufacturer declines all liability 

for injury to persons or animals and for damage to property resulting from 

failure to observe the above regulations. For the electrical connection use a 

H05RR-F type cable as indicated in the table below:

Power supply voltage.

Conductors

Amount x size

220-240V ~ +

230-240V ~ +

380-425V 2N~ +

220-240V 3~ +

380-415V 3N~ +

3 x 4 mm2

3 x 4 mm2 (Australia only)

4 x 1,5 mm2

5 x 1,5 mm2

4 x 1,5 mm2

The appliance must be connected to the electricity supply by means 

of an all-pole disconnect switch with minimum contact gap of 3 mm.
Attention: 

the power supply cable must be long enough to allow the cooktop to 

be removed from the worktop and must be positioned so as to avoid damage 

or overheating caused by contact with the base.

Connecting to the terminal board

Note:

 the yellow/green earth wire must be connected to the terminal with the 

symbol   and must be longer than the other wires.

•  Remove approx. 70 mm of the cable sheath from the power supply cable 

(

B

).

•  Strip approx. 10 mm of sheath from the wires. Then insert the power supply 

cable into the cable clamp and connect the wires to the terminal block as 

indicated in the connection diagram placed close to the terminal block itself.

•  Secure the power supply cable (

B

) by means of the cable clamp.

•  Close the terminal board with the cover (

A

) securing it with the screw 

provided.

•  After the electrical connection, fit the hob from the top and hook it to the 

support springs, according to the illustration.

•  Use pots and pans whose bottom diameter is equal to that of the cooking 

zone or slightly larger.

•  Only use flat-bottomed pots and pans.

•  If possible, keep pot lids on when cooking.

•  Cook vegetables, potatoes, et. with little water in order to cut down cooking 

time.

•  A pressure cooker allows you to save even more energy and time.

ENERGY SAVING TIPS

NO!

Summary of Contents for HR 612 CH









Reviews: