GB
11
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Maintenance and care
Caution! Before cleaning or servicing the unit,
disconnect it from the mains by pulling the power plug
or disconnecting the main circuit breaker.
First cleaning
• Remove the protective film
• Clean with a damp sponge and a little neutral soap
• Rinse off with a damp cloth
• Dry with a soft cloth; if the hood is stainless steel, dry
along the metal's grain
Periodic cleaning
The hood must be cleaned frequently (at least as often as
you service the grease filter), inside and out. Use a damp
cloth and a neutral liquid detergent with lukewarm water.
Do not use abrasive or corrosive products.
Warning:
Failure to observe the hood cleaning and filter
cleaning/replacement instructions can result in fires. Follow
the instructions carefully. The manufacturer is not liable for
any damage to the motor or fires caused by incorrect care
or failure to follow the above instructions.
Servicing the grease filter (A)
A
The grease filter retains the
particles of grease produced
during cooking; it must be
cleaned at least once a month
w i t h a n o n - a g g r e s s i v e
detergent, either by hand or
with a low temperature, short
dishwasher cycle.
To extract the grease filter,
pull the spring loaded handle.
If washed in a dishwasher, the metal filter may change
colour, but this does not affect its performance.
Servicing the charcoal filter (B)
B
The charcoal filter retains
unpleasant cooking odours.
The filter saturates after a
variable time, depending on
the type of cooking and how
often the grease filter is
cleaned. The cartridge must
be replaced at least once
every twenty months.
This filter can NOT be washed
or regenerated
Disassembly:
Rotate the filter 90° to remove it from the
suction assembly.
Assembly:
Fit the active-carbon filter into the suction
assembly and rotate it 90° to secure it in place.
Replacing the bulbs
Disconnect the unit from the mains and remove the grease
filter.
Caution!
Make sure the bulbs are cool before touching
them.
1. Extract the guard
by prising it out with a small
flat head screwdriver or
something similar.
2. Replace the faulty bulb.
Use only bulbs of the
same type (for details,
see the technical data in
the following manual).
3. Refit the guard (push it in).
Replacing the lights LED
*
The hood is fitted with a lighting system based on LED
technology. The LEDs ensure optimal lighting, longer life
and lower consumption compared with traditional lights. To
replace them please contact the assistance service.
Electrical cable
If the power cable is damaged, it can be replaced by the
manufacturer or his technical service, to prevent any
attendant risks.
SCRAPPING
The unit is marked for conformity with European Directive
2012/19/EC, Waste Electrical and Electronic Equipment
(WEEE). By ensuring that the unit is scrapped properly,
the user contributes to safeguarding the environment and
public health.
The
symbol on the product or on its accompanying
documents indicates that the product may not be treated
as domestic waste but must be handed over to a sorting
centre for electrical and electronic waste. Dispose of it
in accordance with local waste disposal regulations. For
further information on the handling, recovery and recycling
of this product, contact the local authority, domestic waste
disposal service or the reseller from whom you purchased it
*
Only available in certain models
GB
Summary of Contents for HHP6.5CM
Page 2: ...2 6x Ø 8 x 40 6x Ø 5 x 45 1x 2x 1x ø 150 125mm ø 150mm 1x 2x 4x Ø 3 5 x 9 5 2 3 4 5 ...
Page 3: ...3 32 cm min 1A Ø150mm 1B Ø150mm Ø120mm Ø120 Ø150 Ø120mm Ø120 Ø150 Ø150mm ...
Page 4: ...4 4 6 3 7 5 2 650 m m 550 m m x6 Ø 8 mm x6 x6 x2 5 m m ...
Page 5: ...5 11 10 x2 ø 150 ø 120 12 13 8 9 1 2 3 x2 ...
