Hotone Binary Eko Owner'S Manual Download | Manualshive

Page: 21 / 21

background image

DESIGN

INSPIRATION

Numbers of Effects: 17
Numbers of Patches: 10 (2 banks x 5 patches)
Max. Delay Time: 4000ms
Digital Processing: 24-bit A/D/A conversion, 44.1 kHz sample rate
Frequency Response: 20 Hz-20 kHz
S/N Ratio: Up to 110dB
Input Impedance: 1M Ohms
Output Impedance: 100 Ohms
Power Requirement: DC 9V, center negative
Current Consumption: 200mA minimum
Dimensions: 121mm (D) x 72mm (W) x 47mm (H)
Weight: 340g

The contents of this manual are subject to change without notice.

Specifications

«
...
19
20
21

Summary of Contents for Binary Eko






















Reviews:

No comments

Related manuals for Binary Eko

Brand: Calrec Pages: 144

Brand: Mackie Pages: 32

FRACTAL PARAMETRIC OVERDRIVE

Brand: aion Pages: 10

Brand: argon audio Pages: 10

MOODY FUZZ v3.2

Brand: MOODY Pages: 5

Brand: MCF Pages: 53

Brand: T-Rex Pages: 5

REPLAY BOX DELAY

Brand: T-Rex Pages: 5

Brand: T-Rex Pages: 5

Brand: T-Rex Pages: 5

Brand: T-Rex Pages: 6

Brand: T-Rex Pages: 5

Brand: T-Rex Pages: 11

ALIGN SERIES SESSION

Brand: L.R. Baggs Pages: 8

ToolMod Faderbox

Brand: adt-audio Pages: 60

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands