manualshive.com logo in svg

Hospira LifeCare XL Series, Technical & Service Manual

Share
Download
Hospira LifeCare XL Series Technical & Service Manual Download Page 111

SECTION 7 REPLACEABLE PARTS AND REPAIRS

430-00587-008 (Rev. 2/05)

7 - 32

Plum XL Series

Figure 7-15.

Buzzer PWA

7.2.9

MAIN CHASSIS ASSEMBLY COMPONENT 
REPLACEMENT

Main chassis assembly component replacement includes the replacement of the following:

❏

MCU PWA and sensor/MCU cable assembly

❏

Mechanism assembly

❏

Cassette door and mechanism shield

❏

Opener handle assembly

Note:

The MCU PWA is not supplied with the main chassis assembly; however, the

MCU PWA is located in the main chassis assembly.

04K01038

6-32 x 3/8

HEX HEAD

SCREW (4)

BUZZER 

PWA

REAR ENCLOSURE

MCU/BUZZER

CABLE ASSEMBLY

AUDIBLE

GASKET

LOCKOUT

GASKET

Summary of Contents for LifeCare XL Series























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands