background image

MAN0969-02                                                   PAGE 6                                                  Mix577/977 Module 

 

 
                                                                                                           

                                                    

 

 

Adhere to the following safety precautions whenever any type of connection is made to the module.  

 

Connect the green safety (earth) ground first before making any other connections.  

 

When connecting to electric circuits or pulse-initiating equipment, open their related breakers.  
Do not make connections to live power lines.    

 

Make connections to the module first; then connect to the circuit to be monitored.   

 

Route power wires in a safe manner in accordance with good practice and local codes. 

 

Wear  proper  personal  protective  equipment  including  safety  glasses  and  insulated  gloves 
when making connections to power circuits.  

 

Ensure hands, shoes, and floor are dry before making any connection to a power line.  

 

Make  sure  the  unit  is  turned  OFF  before  making  connection  to  terminals.    Make  sure  all 
circuits are de-energized before making connections.  

 

Before  each  use,  inspect  all  cables  for  breaks  or  cracks  in  the  insulation.    Replace 
immediately if defective.  

 

TECHNICAL SUPPORT 

 

North America: 

Tel:  317 916-4274 
Fax: 317 639-4279 
Web:    

http://www.heapg.com

  

Email:  

[email protected]

 

Europe: 

Tel:  +353-21-4321266 
Fax: +353-21-4321826 
Web:    

http://www.horner-apg.com

 

Email:  

[email protected]

 

 

 

Cscape, SmartStix and CsCAN are trademarks of Horner APG. This information is subject to change without notice. 

Summary of Contents for SmartBlock HE579MIX577







Reviews: