background image

EN

dynamIte 15t brushed motor

  / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

PrecautionS

 

»

Never touch moving parts.

 

»

Never disassemble while  

the batteries are installed.

 

»

Always let parts cool  

before touching.

coMeS With Std kit

BruShed  

Motor

recoMMended 

BruShleSS Motor

Motor Mount 

Plate PoSition

1st

final (2.66) total 

Gear ratio Motor Plate PoSition

Pinion Spur Drive

Ring

DYN1172  

15 turn 

motor

Brushless motor  

10.5 turn or less

a

22

77

12

32

9.33

STD 77T Spur Gear with 

minimum Pinion Gear

b

23

77

12

32

8.93

C

24

77

12

32

8.56

d

25

77

12

32

8.21

e

26

77

12

32

7.90

f

27

77

12

32

7.60

STD 77T Spur Gear with 

max Pinion Gear

G

28

77

12

32

7.33

h

29

77

12

32

7.08

I

30

77

12

32

6.84

a

28

71

12

32

6.76

Optional 71T Spur Gear with 

minimum Pinion Gear

b

29

71

12

32

6.53

C

30

71

12

32

6.31

Optional 71T Spur Gear  

with max Pinion Gear

d

31

71

12

32

6.11

e

32

71

12

32

5.92

Brushless motor  

13.5 turn

e

38

65

12

32

4.56

Optional 65T Spur Gear 

with minimum Pinion Gear

f

39

65

12

32

4.44

G

40

65

12

32

4.33

h

41

65

12

32

4.23

Optional 65T Spur Gear 

with max Pinion Gear

I

42

65

12

32

4.13

VTR232044

VTR232050

Summary of Contents for Vaterra Chevrolet Camaro ZL1 2012




















Reviews: