5
EN
LOSI
®
SUPER BAJA REY
®
2.0, SMART ESC:1/6TH 4WD RTR • INSTRUCTION MANUAL
DRIVING PRECAUTIONS
• Maintain sight of the vehicle at all times.
• Routinely inspect the vehicle for loose wheel hardware.
• Routinely inspect the steering assembly for any loose hardware. Driving the vehicle off-road
can cause fasteners to loosen over time.
• Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics.
• Stop driving the vehicle when you notice a lack of power. Driving the vehicle when the
battery is discharged can cause the receiver to power off. If the receiver loses power, you
will lose control of the vehicle. Damage due to an over-discharged Li-Po battery is not
covered under warranty.
CAUTION:
Do not discharge a Li-Po battery below 3V per cell. Batteries
discharged to a voltage lower than the lowest approved voltage may become
damaged, resulting in loss of performance and potential fire when batteries are charged.
• Do not apply forward or reverse throttle if the vehicle is stuck.
Applying throttle in this instance can damage the motor or ESC.
• After driving the vehicle, allow the electronics to cool before driving the vehicle again.
IMPORTANT:
Keep wires away from all moving parts.
BEFORE RUNNING THE VEHICLE
1. Check for free suspension movement. All suspension arms and steering components should
move freely. Any binds will cause the vehicle to handle poorly.
TIP:
To increase the ride height and ground clearance of your vehicle, screw down the
shock collars to compress the springs.
2. Charge a battery pack. Always charge the battery pack as per the battery and/or charger
manufacturers’ instructions.
3. Set the transmitter steering trim. Follow the instructions to set the steering trim/subtrim so
that the vehicle drives straight with no input to the steering.
4. Perform a Control Direction Test.
AVC
®
SENSITIVITY
The ST RATE dial adjusts the sensitivity, or stability, value in the receiver. If you increase the
sensitivity, the AVC
®
system becomes more sensitive to the vehicle drifting left or right. You
would use maximum sensitivity during high speed driving or drag racing, when you want the
vehicle to stay in a straight line.
Turn the ST RATE knob counter-clockwise to reduce the sensitivity.
Turn the ST RATE knob clockwise to increase the sensitivity.
IMPORTANT:
The ST RATE knob will only adjust the sensitivity when the
transmitter is bound to a DSMR
®
receiver. When the transmitter is bound
to a DSM
®
, DSM2
®
or DSM Marine receiver, the ST RATE knob controls
the steering dual rate.
BINDING AND CALIBRATING THE RECEIVER
Binding is the process of linking the SR6100AT receiver to your Spektrum transmitter. The AVC
features on the receiver can be enabled or disabled during the binding process.
IMPORTANT:
You must calibrate the SR6100AT receiver each time it is placed in bind mode,
regardless of AVC being enabled or disabled.
Upon initial setup after the first bind, the model must be configured for servo direction, trim
and travel. Then the receiver must be rebound and calibrated to those settings for proper
operation. Center the steering trim and throttle trim on the transmitter before beginning.
1. Press and hold the bind button on the receiver.
2. Power on the receiver. The orange LED flashes, indicating the receiver is in bind mode.
Release the bind button after the orange LED illuminates.
3. Put your transmitter in bind mode. The bind process is complete when the orange LED
on the receiver remains lit. The receiver is now bound to the transmitter but must be
calibrated before it will operate.
4. Pull the transmitter trigger to full throttle, pause, then return the trigger to center.
5. Push the transmitter trigger to full brake, pause, then return the trigger to center.
6. Turn the transmitter steering wheel to full right, pause, then return the wheel to center.
7. Turn the transmitter steering wheel to full left, pause, then return the steering wheel to
center. The orange LED flashes to confirm the settings have been accepted.
8. Turn off the vehicle to complete the binding and calibration process.
CAUTION:
When the bind process is complete, the throttle and steering channels
are active. Keep hands and loose objects away from all spinning parts on the
vehicle.
IMPORTANT:
You must rebind the transmitter and receiver if you:
• Change the servo reversing after binding
• Change the travel after binding
• Change the receiver mounting orientation
DISABLING AVC
®
TECHNOLOGY STABILITY ASSIST
If you participate in organized racing, you may be required to turn AVC technology off.
To turn off AVC technology:
1. Connect power to the receiver and quickly press and release the bind button three times
(within 1.5 seconds).
2. Press and hold the bind button and to put the receiver in bind mode. release the buton
when the LED starts to flash rapidly, indicating it is in bind mode.
When the AVC system has been disabled, the LED on the receiver will show three flashes
upon power up, and then remain lit. The receiver is bound and operating normally when the
LED remains illuminated.
TIP:
If the AVC feature in the receiver is active and the AVC menu in the transmitter is
Inhibited, AVC functions will default to the AUX 1 and AUX 2 operation, and in this scenario,
AVC will not work correctly.
FAILSAFE
In the unlikely event that the radio link is lost during use, the receiver will drive the throttle
channel to the neutral position. If the receiver is powered on prior to turning on the
transmitter, the receiver will enter the failsafe mode, driving the throttle channel to the neutral
position. When the transmitter is turned on, normal control is resumed.
IMPORTANT:
Failsafe activates only in the event that signal is lost from the transmitter.
Failsafe will NOT activate in the event that receiver battery power decreases below the
recommended minimums or power to the receiver is lost.
SR6100AT AVC TECHNOLOGY TELEMETRY RECEIVER
AUX CHANNELS
The Aux channels can operate as additional servo channels, or as a power supply
for a personal transponder.
If AVC is active, only 4 channels; Steering, Throttle, AUX3 and AUX4 are operational.
The reaming Aux channels can be used to power a personal transponder or lights.
If AVC is disabled (see DISABLING AVC TECHNOLOGY STABILITY ASSIST FUNCTION),
all 6 channels including the Aux channels can operate as servo channels.
AUX 1 Port
AUX 2 Port
AUX 3 Port
AUX 4 Port
Battery/Programming Port
Throttle Port
Steering Port
Bind Button
FULL THROTTLE
BRAKE/REVERSE