background image

14

EN

purchase is required for all warranty claims. SERVICE OR 
REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS 
THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY. 

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, 
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF 
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY 
WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED 
IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT 
LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF 
HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF 
SUCH DAMAGES. Further, in no event shall the liability 
of Horizon exceed the individual price of the Product on 
which liability is asserted. As Horizon has no control over 
use, setup, fi nal assembly, modifi cation or misuse, no 
liability shall be assumed nor accepted for any resulting 
damage or injury. By the act of use, setup or assembly, the 
user accepts all resulting liability. If you as the purchaser 
or user are not prepared to accept the liability associated 
with the use of the Product, purchaser is advised to return 
the Product immediately in new and unused condition to 
the place of purchase.

Law

These terms are governed by Illinois law (without regard to 
confl ict of law principals).  This warranty gives you specifi c 
legal rights, and you may also have other rights which vary 
from state to state.  Horizon reserves the right to change 
or modify this warranty at any time without notice.

WARRANTY SERVICES
Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot 
provide warranty support or service. Once assembly, setup 
or use of the Product has been started, you must contact 
your local distributor or Horizon directly. This will enable 
Horizon to better answer your questions and service 
you in the event that you may need any assistance. For 
questions or assistance, please visit our website at www.
horizonhobby.com, submit a Product Support Inquiry, 
or call the toll free telephone number referenced in the 
Warranty and Service Contact Information section to speak 
with a Product Support representative. 

Inspection or Services

If this Product needs to be inspected or serviced and is 
compliant in the country you live and use the Product in, 
please use the Horizon Online Service Request submission 
process found on our website or call Horizon to obtain a 
Return Merchandise Authorization (RMA) number. Pack 
the Product securely using a shipping carton. Please note 
that original boxes may be included, but are not designed 
to withstand the rigors of shipping without additional 
protection. Ship via a carrier that provides tracking and 
insurance for lost or damaged parcels, as Horizon is not 
responsible for merchandise until it arrives and is accepted 

at our facility. An Online Service Request is available at 
http://www.horizonhobby.com/content/service-center_
render-service-center. If you do not have internet access, 
please contact Horizon Product Support to obtain a RMA 
number along with instructions for submitting your product 
for service. When calling Horizon, you will be asked to 
provide your complete name, street address, email address 
and phone number where you can be reached during 
business hours. When sending product into Horizon, please 
include your RMA number, a list of the included items, and 
a brief summary of the problem.  A copy of your original 
sales receipt must be included for warranty consideration. 
Be sure your name, address, and RMA number are clearly 
written on the outside of the shipping carton. 

NOTICE: Do not ship LiPo batteries to Horizon. If you 
have any issue with a LiPo battery, please contact 
the appropriate Horizon Product Support offi ce.

Warranty Requirements
For Warranty consideration, you must include your 
original sales receipt verifying the proof-of-purchase 
date.

 Provided warranty conditions have been met, your 

Product will be serviced or replaced free of charge. 
Service or replacement decisions are at the sole discretion 
of Horizon.

Non-Warranty Service
Should your service not be covered by warranty, 
service will be completed and payment will be 
required without notifi cation or estimate of the 
expense unless the expense exceeds 50% of the retail 
purchase cost

. By submitting the item for service you are 

agreeing to payment of the service without notifi cation. 
Service estimates are available upon request. You must 
include this request with your item submitted for service. 
Non-warranty service estimates will be billed a minimum 
of ½ hour of labor. In addition you will be billed for return 
freight. Horizon accepts money orders and cashier’s 
checks, as well as Visa, MasterCard, American Express, 
and Discover cards. By submitting any item to Horizon 
for service, you are agreeing to Horizon’s Terms and 
Conditions found on our website http://www.horizonhobby.
com/content/service-center_render-service-center. 

ATTENTION:  Horizon service is limited to Product 
compliant in the country of use and ownership. 
If received, a non-compliant Product will not be 
serviced. Further, the sender will be responsible 
for arranging return shipment of the un-serviced 
Product, through a carrier of the sender’s choice 
and at the sender’s expense. Horizon will hold 
non-compliant Product for a period of 60 days from 
notifi cation, after which it will be discarded.

10/15

Summary of Contents for E-flite UMX Turbo Timber



















Reviews: