Horizon Hobby E-flite Su-30 Instruction Manual Download Page 19

EN

19

AMA National Model Aircraft Safety Code

Effective January 1, 2014

A. GENERAL

A model aircraft is a non-human-carrying aircraft capable of sustained fl ight in the 
atmosphere. It may not exceed limitations of this code and is intended exclusively 
for sport, recreation, education and/or competition. All model fl ights must be 
conducted in accordance with this safety code and any additional rules specifi c to 
the fl ying site.

1. Model aircraft will not be fl own:

(a) In a careless or reckless manner.
(b) At a location where model aircraft activities are prohibited.

2. M odel aircraft pilots will:

(a) Yield the right of way to all man carrying aircraft.
(b) See and avoid all aircraft and a spotter must be used when appropriate. 

(AMA Document #540-D.)

(c) Not fl y higher than approximately 400 feet above ground level within three 

(3) miles of an airport, without notifying the airport operator.

(d) Not interfere with operations and traffi c patterns at any airport, heliport or 

seaplane base except where there is a mixed use agreement.

(e) Not exceed a takeoff weight, including fuel, of 55 pounds unless in 

compliance with the AMA Large Model Aircraft program. (AMA Document 
520-A.)

(f) Ensure the aircraft is identifi ed with the name and address or AMA number 

of the owner on the inside or affi xed to the outside of the model aircraft. 
(This does not apply to model aircraft fl own indoors).

(g) Not operate aircraft with metal-blade propellers or with gaseous boosts 

except for helicopters operated under the provisions of AMA Document 
#555.

(h) Not operate model aircraft while under the infl uence of alcohol or while 

using any drug which could adversely affect the pilot’s ability to safely 
control the model.

(i) Not operate model aircraft carrying pyrotechnic devices which explode 

or burn, or any device which propels a projectile or drops any object that 
creates a hazard to persons or property.

Exceptions:
•  Free Flight fuses or devices that burn producing smoke and are securely 

attached to the model aircraft during fl ight.

•  Rocket motors (using solid propellant) up to a G-series size may be used 

provided they remain attached to the model during fl ight. Model rockets 
may be fl own in accordance with the National Model Rocketry Safety 
Code but may not be launched from model aircraft.

•  Offi cially designated AMA Air Show Teams (AST) are authorized to use de-

vices and practices as defi ned within the Team AMA Program Document 
(AMA Document #718).

(j) Not operate a turbine-powered aircraft, unless in compliance with the AMA 

turbine regulations. (AMA Document #510-A).

3. Model aircraft will not be fl own in AMA sanctioned events, air shows or model 

demonstrations unless:
(a) The aircraft, control system and pilot skills have successfully demonstrated 

all maneuvers intended or anticipated prior to the specifi c event.

(b) An inexperienced pilot is assisted by an experienced pilot.

4. When and where required by rule, helmets must be properly worn and 

fastened. They must be OSHA, DOT, ANSI, SNELL or NOCSAE approved or 
comply with comparable standards.

B. RADIO CONTROL

1. All pilots shall avoid fl ying directly over unprotected people, vessels, vehicles or 

structures and shall avoid endangerment of life and property of others.

2. A successful radio equipment ground-range check in accordance with 

manufacturer’s recommendations will be completed before the fi rst fl ight of a 
new or repaired model aircraft.

3. At all fl ying sites a safety line(s) must be established in front of which all fl ying 

takes place (AMA Document #706.)
(a) Only personnel associated with fl ying the model aircraft are allowed at or in 

front of the safety line.

(b) At air shows or demonstrations, a straight safety line must be established.
(c) An area away from the safety line must be maintained for spectators.
(d) Intentional fl ying behind the safety line is prohibited.

4. RC model aircraft must use the radio-control frequencies currently allowed 

by the Federal Communications Commission (FCC). Only individuals properly 
licensed by the FCC are authorized to operate equipment on Amateur Band 
frequencies.

5. RC model aircraft will not operate within three (3) miles of any pre-existing 

fl ying site without a frequency-management agreement (AMA Documents #922 
and #923.)

6. With the exception of events fl own under offi cial AMA Competition Regulations, 

excluding takeoff and landing, no powered model may be fl own outdoors closer 
than 25 feet to any individual, except for the pilot and the pilot’s helper(s) 
located at the fl ight line.

7. Under no circumstances may a pilot or other person touch a model aircraft in 

fl ight while it is still under power, except to divert it from striking an individual. 

8. RC night fl ying requires a lighting system providing the pilot with a clear view 

of the model’s attitude and orientation at all times. Hand-held illumination 
systems are inadequate for night fl ying operations.

9. The pilot of a RC model aircraft shall:

(a) Maintain control during the entire fl ight, maintaining visual contact without 

enhancement other than by corrective lenses prescribed for the pilot.

(b) Fly using the assistance of a camera or First-Person View (FPV) only in 

accordance with the procedures outlined in AMA Document #550.

(c) Fly using the assistance of autopilot or stabilization system only in 

accordance with the procedures outlined in AMA Document #560.

Please see your local or regional modeling association’s guidelines for proper, 
safe operation of your model aircraft.

Summary of Contents for E-flite Su-30























Reviews: