hopf 8029HEPTA-V2/GPS Technical Manual Download Page 82 | Manualshive

Page: 82 / 130

background image

HTTP/HTTPS

W

EB

GUI

–

W

EB

B

ROWSER

C

ONFIGURATION

I

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

82 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3.4.2 E-mail Configuration

E-mail notification is one of the important features of this device which offers technical
personnel the opportunity to monitor and/or control the IT environment.

It is possible to configure various, independing E-mail addresses which each have different
alarm levels.

Dependending on the configured level, an E-mail is sent after an error has occurred on the
respective receiver.

A valid E-mail server (SMTP server) must be entered for the purpose of correct configuration.

Some E-mail servers only accept messages if the sender address entered is valid (spam
protection). This can be inserted in the “Sender Address” field.

The Alarm Level designates the priority level of the messages to be sent and determines from
which level the message should be sent (see

Chapter 8.3.4.4 Alarm Messages

).

Alarm Level

Transmitted Messages

none

no messages

info

info / warning / error / alarm

warning

warning / error / alarm

error

error / alarm

alarm

alarm

«
...
80
81
82
83
84
...
»

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Reviews:

No comments

Related manuals for 8029HEPTA-V2/GPS

Brand: ABB Pages: 64

Brand: Gaggenau Pages: 74

Brand: Mallory Pages: 2

Brand: Evenheat Pages: 17

Brand: Bodet Pages: 10

Brand: KUSSMAUL Pages: 1

Brand: Co2meter Pages: 14

WT 5100 - CONNECTION SCHEMA

Brand: VDO Pages: 1

Brand: VDO Pages: 2

Brand: Ferplast Pages: 48

Brand: GeoVision Pages: 15

Brand: Aqua One Pages: 8

Brand: Oase Pages: 166

Brand: LaBina Pages: 18

Brand: KAT VR Pages: 34

Brand: Paradyne Pages: 324

Brand: Eaton Pages: 52

Brand: Lascar Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands