hopf 8029HEPTA-V2/GPS Technical Manual Download Page 13

Page: 13 / 130

YSTEM

TRUCTURE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

13 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

2.1

19 inch Rack 1U/84HP (Slim Line)

2.2

Functional Overview of the Front Panel Elements

This chapter describes the individual function elements of the front and rear panel.

2.2.1 LCD-Display with Pushbutton

The background illumination of the LCD-Display is activated or rather controlled by the
pushbutton Light/Scroll.

The 2x40 LCD-Display enables reading out the time and further essential information for the
commissioning, the operation status, and for support even without WebGUI access.

The operation and function of the pushbutton and the display are described in

Chapter 7 LCD-

Display with Pushbutton

– Function

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands