hopf 8029HEPTA-V2/GPS Technical Manual Download Page 107

Page: 107 / 130

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

107 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3.6.14 Sync Status OC

The output of the status optical coupler (on the back panel of the Time Server
8029HEPTA/GPS) can be configured by the use of this function.

The Sync states are listed in this selection window in rising quality from the bottom to the top
(

SYNC

= optimal condition).

Behaviour of Optical Coupler:

•

Selected status achieved or better

– Optical coupler switched through

•

Selected status not achieved

– Optical coupler blocked

Value range

Optical Coupler Status

SYNC

Time synchr Quartz regulation started/running

SYOF

Time synchr SyncOFF running

SYSI

Time synchronized as simulation mode
(without actual GPS reception)

QUON

Quartz/Crystal time + SyncON running

QUEX

Quartz/Crystal time (in freewheel after synchronization
failure



Board was already synchronized)

QUSE

Quartz/Crystal time after reset or manual setting

INVA

Invalid time

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands