Hoover U57809RM Windtunnel Cyclonic, Owner'S Manual, Page: 11 / 20

11
With lettering on
outside of belt, slide
new belt over motor
shaft (A).
Place other end of
belt over large pulley
(B) while rolling the
pulley in direction
shown.
Turn agitator brush roll making sure belt turns
freely and is not pinched between agitator brush
roll and agitator shield.
Belts
The belts are located under the bottom plate of the cleaner and should be checked from time to time
to be sure they are in good condition.
Disconnect cleaner from electrical outlet.
WARNING: Agitator brush roll can start suddenly. Unplug cleaner before turning it over.
Replacing Flat Belt
Place handle in low
position and turn
cleaner over so bottom
side is facing up.
Remove the 6 screws as
shown with a Phillips
screwdriver.
Lift off bottom plate.
4-13 4-14
Replace belt if it is stretched, cut or broken. To check the flat belt, refer to Fig. 4-13.
Removing Bottom
Plate Removing Belt
Positioning Belt
Remove used belt (A)
from large pulley (B)
and discard.
Reposition bottom plate
and 6 Phillips head
screws. Tighten screws
securely.
Insert agitator brush
roll through belt
and position belt in
groove (A) on agitator
brush roll.
4-18
Inspecting V-Belt
The V-belt is designed to last for a long time and
is not normally replaced. However, if the V-belt is
cracked, gouged or broken, it should be replaced.
Slide flat belt off large pulley as shown in Fig. 4-14.
To remove V-belt, slide back of belt over pulley (A).
Then firmly pull on belt and “snap” it out.
Discard used belt.
To install new belt (with lettering on outside of
belt), slide back of belt over pulley and pull front of
belt toward groove (B) next to pulley. Belt will “pop” into place.
4-17
4-16
Flat Belt: What to Buy
Use only genuine HOOVER belts with your
cleaner. When purchasing a new belt, ask for
Flat belt - HOOVER part No. 40201-271.
V-Belt: What to Buy
Use only genuine HOOVER belts with your cleaner. When purchasing a
new belt, ask for V belt - HOOVER part No. 40201-200.
4-15
A
B
A
B
A
B
A
11
Fai re glis ser la
nou vel le cou rro ie
sur l’a rbr e m ote ur
(A ) e n s ’as sur ant
que le le ttr age de
la cou rro ie est ve rs
l’e xté rie ur.
Pla cer l’a utr e
ext rémi té de la
cou rro ie sur la
gra nde po ulie (B )
en fai san t to urn er l a
pou lie da ns la dire cti on ind iqué e.
Fai re tou rne r le ro ule au- bro sse ag ita teu r p our
s’a ssu rer qu ’il tou rne lib rem ent et que la co urr oie
n’e st pas coi ncé e e ntr e le ro ule au- bro sse ag ita teu r
et le pro tèg e-r oul eau.
La Courroie
S’as su rer d e la b onn e con dit ion d es c our roi es. S itu ées s ous l a pla que i nfé rie ure d e l’a spi rat eu r, e lle s
dev rai ent ê tre v éri fié es r ég uliè rem ent .
Déb ran che r l’ app are il de la pr ise de co ura nt.
AVE RTI SSE MEN T : Le rou leau-b ros se agit ateur peu t s e m ett re en mar che br usqu em ent . D ébr anch er
l’a spi rat eur a van t d e le m ett re à l’ env ers .
Remplacement de la courroie plate
Pla cer le m anc he à s a
pos itio n b ass e e t re tou rne r
l’a ppa rei l à l’e nve rs.
À l’ aid e d ’un to urn evi s
cru cifo rm e, r eti rer le s
six (6 ) v is, co mm e il est
illu stré .
Enl eve r la pl aqu e in fér ieu re.
4-13 4-14
Rem pla cer la co urro ie si e lle est ét iré e, c oup ée ou sec tio nné e. P our vé rifi er l a c our roi e p lat e, c ons ulte r la Fi g. 4 -13 .
Dépose de la
plaque inférieure
Dépose de la
courroie
Placement de la courroie
Enl eve r la c our roi e
usé e (A ) de l a gra nde
pou lie ( B) e t la j ete r.
Rem ett re en pla ce la
pla que in fér ieu re et les
six (6 ) v is cru cif orm es.
Ser rer sol ide men t le s v is.
Ins ére r le ro ule au-
bro sse ag ita teur
dan s la co urr oie pu is
pla cer la co urr oie
dan s la ra inu re (A ) d e
l’a git ate ur.
4-18
Inspection de la courroie en V
La c our roi e en V e st c onç ue p our d ure r lon gte mps
et h abi tu elle men t elle n ’a p as b eso in d ’êt re
rem pla cée . Tou tef ois , si l a cou rro ie e n V est é tir ée,
cou pée o u sec tio nné e, e lle d oit ê tre r em pla cée .
Fai re g lis ser l a cou rro ie p lat e hor s de l a gra nde
pou lie , com me i l est i llu str é à la f ig ure 4 -14 .
Pou r enl eve r la c our roi e en V , fai re g lis ser l e des su s
de l a cou rro ie p ar- des su s la p oul ie ( A). P uis t ire r
fer mem ent l a cou rro ie e t l’e xpu lse r.
Jet er l a cou rro ie u sée .
Pou r ins tal ler u ne n ou vel le c our roi e (av ec l e
let tra ge v ers l ’ex tér ieu r), f air e glis ser l e des su s de l a cou rro ie p ar- des su s
la p oul ie e t tir er l e des sou s de l a cou rro ie v ers l a rai nur e (B ) qui s e tro uve
prè s de l a pou lie . La c our roi e “s’e ncl enc he“ a lor s en p lac e.
4-17
4-16
La Courroie Plate: Quoi acheter?
N’u til ise r que d es c our roi es o rig ina les
HO OV ER a vec v otr e asp ira teu r. À l ’ac hat
d’u ne n ou vel le c our roi e, d em and er l a
cou rro ie pla te, piè ce HO OV ER n° 402 01- 271.
La Courroie en V: Quoi acheter?
N’u tili ser qu e d es c our roi es o rig ina les HO OVE R a vec vo tre as pira teu r. À l’a cha t
d’u ne n ouv elle co urro ie, dem and er l a co urro ie e n V , p ièc e H OOV ER n° 4 020 1-2 00.
4-15
A
B
A
B
A
B
A