04 GB
2.3. ADAPTING THE HOB TO DIFFERENT
TYPES OF GAS
To adapt the Hob for use with different types of gas, carry out the
following instructions:
•Remove the grids and burners
•Unscrew the injector and replace it with one suitable for the gas to be
used
(see gas type table)
•Insert on hexagonal spanner (7 mm) into the burner support
(Figure7)
2.4. REGULATING THE MINIMUM FLAME
Using a small «Terminal» type screwdriver the regulating screw can
be adjusted as in
Turning the screw clockwise reduces the
gas flow, whilst turning it anticlockwise increases the flow – Use this
adjustment to obtain a flame of approximately 3 to 4 mm in length and
then replace the control knob.
Figure 9.
When you have carried out the new gas regulation, replace the old gas
rating plate on your appliance with one (supplied with hob) suitable for
the type of gas for which it has been regulated.
After lighting the burners, turn the control knob to the minimum setting
and then remove the knob (this can easily be removed by applying
gentle pressure).
When the gas supply available is LPG - the screw to set the idle flame
must be turned (clockwise) to the end stop.
3. USE OF HOB - USER INSTRUCTIONS
Before using burner, be sure, grid perimeters center the burner as
below figure.
This appliance must only be used for the purpose for which it is
intended, domestic cooking, and any other use will be considered
improper and could therefore be dangerous. The Manufacturer will
not be responsible for any damage or loss resulting from improper
use.
If you are using Cast Iron Grids; underneath the grid, position of it is
stated. Be sure for the exact grid is used in correct position.
Table A
Burner Type
Ø pan/pot
(cm)
AUX
SR
R
10 - 18
12 - 22
16 - 26
Auxiliary
Semi Rapid
Rapid
Power
(kW)
1,00
1,75
2,70
G20 20 mbar
(methane)
95 l/h
167 l/h
257 l/h
G30 28-30 mbar
(LPG)
73 g/h
127 g/h
196 g/h
4. MAINTENANCE AND CLEANING
Never use abrasives, corrosive detergents, bleaching agents or
acids. Avoid any acid or alkaline substances (lemon, juice, vinegar
etc.) on the enamelled, varnished or stainless steel sections.
Before cleaning the hob, ensure the appliance has cooled down.
Remove the plug from the socket or (if connected directly) switch off
the electricity supply.
When cleaning the enamelled, varnished or chrome sections, use
warm soapy water or a non caustic detergent. For stainless steel use
an appropriate cleaning solution.
Chromed grids and burners have a tendency to discolour with use.
This does not jeopardize the functionality of the hob.
The burners can be cleaned with soapy water. To restore their original
shine, use a household stainless steel cleaner. After cleaning, dry the
burners and replace.
It is important the Burners are replaced correctly.
Cleaning and user maintenance shall not be made by children without
supervision
Our After Sales Service Centre can provide spare parts if required.
Chromed grids and burners
If over the years the gas taps become stiff to turn it is necessary to
lubricate them.
Such operation must be carried out only by qualified Service
Engineers.
WARNING: If a flame is accidentally extinguished, turn the knob
to the off position and do not attempt to re-ignite if for at least 1
minute.
The gas burner should be regulated so that the flame does not overlap
the base of the pan. Vessels with a concave or convex base should not
be used.
IMPORTANT: carry out a final check for leaks on the pipe
connections using a soapy solution.
Also, make sure that the flexible pipe cannot come into contact
with a moving part of the cabinet (eg.adrawer) and that it is not
situated where it could be damaged.
NEVER USE A FLAME.
Warning:
If gas can be smelt in the vicinity of this appliance turn off
the gas supply to the appliance and call the engineer directly. Do not
search for a leak with a naked flame.
3.1. USING THE GAS BURNER
° push in and turn the knob anticlockwise to the larger flame symbol
This hob is fitted with electronic ignition to ignite the burner.
To ignite the burners carry out the following:
Warning: If there is no electricity on appliance to ignite the burner a
match or a lighter should be used carring out the following:
and keep pushed 5 s after ignition.
The ignition system will continue to generate sparks as long as the
control knob is being pressed
Prior to switching on the gas hob ensure that the burners and burner
caps are correctly placed within their position.
Warning: In any case If after 5 s the burner has not lit, stop operating
the device and wait at least 1 min before attempting a further ignition
of the burner.
and keep pushed 5 s after ignition.
°push in and turn the knob anticlockwise to the larger flame symbol
°place a lighted match or lighter close to the burner
DC
4 kW Mono
16 - 26
4,00
381 l/h
291 g/h
DC
4,2 kW Mono
16 - 26
4,20 NG
4,00 LPG
400 l/h
291 g/h
DC
4,5 kW Mono
16 - 26
4,50
429 l/h
327 g/h
For best results, use cooking vessels with a flat surface. The size of
the surface should match the gas burner side as follows. Table A.
GENERAL ADVISE
