Honeywell Youjie HH660 User Manual Download

Page: 49 / 164

3 - 9

Poor Quality PDF Codes

This setting improves the scanner’s ability to read damaged or badly printed PDF codes by combining information from mul-
tiple images. When

Poor Quality PDF On

is scanned, poor quality PDF code reading is improved, but the scanner’s snap-

piness is decreased, making it less aggressive when reading good quality bar codes. This setting does not affect 1D bar

code reading.

Default = Poor Quality PDF Reading Off.

CodeGate

When CodeGate is

, the trigger is used to allow decoded data to be transmitted to the host system. The scanner remains on,

scanning and decoding bar codes, but the bar code data is not transmitted until the trigger is pressed. When CodeGate is

Off

bar code data is transmitted when it is decoded.

Default = CodeGate Off Out-of-Stand.

Mobile Phone Read Mode

When this mode is selected, your scanner is optimized to read bar codes from mobile phone or other LED displays. However,

the speed of scanning printed bar codes may be slightly lower when this mode is enabled.

Note: To turn off Mobile Phone Read Mode, scan the Manual Trigger Mode bar code (see page

3-5

Poor Quality PDF Reading On

* Poor Quality PDF Reading Off

* CodeGate Off

Out-of-Stand

CodeGate On

Out-of-Stand

Hand Held Scanning - Mobile

Phone

Presentation Scanning -

Mobile Phone

Summary of Contents for Youjie HH660





































































































































































Search results

Summary of Contents for Youjie HH660

Reviews:

Related manuals for Youjie HH660

Brands by name

Popular brands

Honeywell Youjie HH660, User Manual

Search results

Summary of Contents for Youjie HH660

Reviews:

Related manuals for Youjie HH660

Brands by name

Popular brands