Operating and
Installation Instructions
XW100 Wireless Module
1
3
4
7
8
Thank you for purchasing this X-Series Wireless module.
The symbols above mean that the wireless module is suitable for
use in domestic premises (including static caravan holiday homes),
caravans, motor caravans and boats.
This manual contains important safety information about the
installation and operation of the wireless module. Read the manual
carefully and keep it in a safe place for future reference.
2. Description
3. About wireless interconnection alarms
1. Welcome
All Honeywell X-Series alarms can be wirelessly interconnected
using the XW100 plug-in module. This means that if one X-Series
Carbon Monoxide or smoke or heat alarm triggers an alarm, all
interconnected units will give an audible alarm as well. This is
especially useful, when living in a large or multi-story dwelling
where the alarm may be triggered in another part of the building.
The device includes a wireless module button which is used to
configure and operate the module, a blue Wireless Module LED
which signifies various statuses and an antenna.
Interconnecting smoke, heat and Carbon Monoxide alarms is
essential to provide the earliest possible warning of a danger
in a building. The sooner occupants are alerted to a fire or the
presence of Carbon Monoxide, the lower the risk of death or injury.
Furthermore, the potential for property damage is reduced. Hard
wired interconnection is expensive, time consuming and disruptive
and a hard wired system is difficult and expensive to reconfigure
when circumstances (or standards) change.
Wireless module XW100 provides a solution for the interconnection
of Honeywell’s X-Series alarms. Using XW100 module’s wireless
capabilities, you can easily install your alarm network without the
need for drilling, disturbing pipes or decor. The smoke alarms,
heat alarms and Carbon Monoxide alarms are interconnected
by wireless signals rather than cabling all the X-Series alarms,
creating a safety system that is simpler, more convenient, and
easier to change or extend as and when required. XW100 allows all
the alarms in the network to see each other, allowing for a stronger
and more responsive network.
As there is no wiring required, it allows a quicker, simpler and
more cost effective solution to interconnected residential alarm
installations.
Wireless Module Button
Wireless Module LED
Wireless
Module LED
Antenna
www.homesafety.honeywell.com
www.honeywellanalytics.com
www.honeywell.com
UK customer service centre:
Honeywell Analytics Ltd.
4 Stinsford Road
Nuffield Industrial Estate
Poole, Dorset BH17 0RZ
Tel: +44 (0)1202 645577
Fax: +44 (0)1202 665331
Acts for and on behalf of Life Safety Distribution AG,
Javastrasse 2, 8604 Hegnau, Switzerland by
its Authorised Representative Honeywell Inc.
Please Note:
While every effort has been made to ensure
accuracy in this publication, no responsibility
can be accepted for errors or omissions. Data
may change, as well as legislation, and you
are strongly advised to obtain copies of the
most recently issued regulations, standards,
and guidelines. This publication is not intended
to form the basis of a contract. Please retain
product documentation for the lifetime of
the product.
I56-4255-001
MAN0983_Issue 1_01/15_EN
© 2015 Honeywell Analytics
Contact us
I56-4255-001
For installation of your smoke or Carbon Monoxide alarm, refer to
the alarm’s manual.
1. Use a screwdriver to release the alarm from its mounting plate
2. Turn the alarm over to gain access to the reverse of the alarm
4. Installation
‘Switch off’
operation
3. Place the wireless module in the cavity on the rear of the alarm,
ensuring the antenna is on the side with the exposed connectors
4. Fold the antenna between the alarm outer rim and the module
casing, ensuring it sits beneath the alarm’s outer rim
5. Once the wireless module has been configured, clip the alarm
back onto its mounting plate to reactivate it
Caution: Do not repeatedly insert the wireless module into the host
alarm as that will weaken the module connectors.
Wireless module
secures in place
with header pins
Wireless module
cavity
Wireless module
cavity
Antenna beneath the
alarm’s outer rim
X-Series Smoke Alarm
X-Series Carbon Monoxide Alarm
Locking / release
2
Warnings
If you are in any doubt regarding the cause of an alarm it
should be assumed that the alarm is due to an actual fire or
carbon monoxide leak and the dwelling should be evacuated.
It is the responsibility of the installer to ensure the product is
installed in line with current regulations. If in doubt please
consult a competent professional installer.